Photoelectrochemical Performance of Quantum dot-Sensitized TiO2 Nanotube Arrays: a Study of Surface Modification by Atomic Layer Deposition Coating

Nanoscale Research Letters, Apr 2017

Although CdS and PbS quantum dot-sensitized TiO2 nanotube arrays (TNTAs/QDs) show photocatalytic activity in the visible-light region, the low internal quantum efficiency and the slow interfacial hole transfer rate limit their applications. This work modified the surface of the TNTAs/QDs photoelectrodes with metal-oxide overlayers by atomic layer deposition (ALD), such as coating Al2O3, TiO2, and ZnO. The ALD deposition of all these overlayers can apparently enhance the photoelectrochemical performance of the TNTAs/QDs. Under simulated solar illumination, the maximum photocurrent densities of the TNTAs/QDs with 10 cycles ZnO, 25 cycles TiO2, and 30 cycles Al2O3 overlayers are 5.0, 4.3, and 5.6 mA/cm2 at 1.0 V (vs. SCE), respectively. The photoelectrode with Al2O3 overlayer coating presents the superior performance, whose photocurrent density is 37 times and 1.6 times higher than those of the TNTAs and TNTAs/QDs, respectively. Systematic examination of the effects of various metal-oxide overlayers on the photoelectrochemical performance indicates that the enhancement by TiO2 and ZnO overcoatings can only ascribed to the decrease of the interfacial charge transfer impedance, besides which Al2O3 coating can passivate the surface states and facilitate the charge transfer kinetics. These results could be helpful to develop high-performance photoelectrodes in the photoelectrochemical applications.

A PDF file should load here. If you do not see its contents the file may be temporarily unavailable at the journal website or you do not have a PDF plug-in installed and enabled in your browser.

Alternatively, you can download the file locally and open with any standalone PDF reader:

https://link.springer.com/content/pdf/10.1186%2Fs11671-017-2036-6.pdf

Photoelectrochemical Performance of Quantum dot-Sensitized TiO2 Nanotube Arrays: a Study of Surface Modification by Atomic Layer Deposition Coating

Zhou et al. Nanoscale Research Letters Photoelectrochemical Performance of Quantum dot-Sensitized TiO Nanotube 2 Arrays: a Study of Surface Modification by Atomic Layer Deposition Coating Quan Zhou 0 1 Junchen Zhou 0 1 Min Zeng 0 1 Guizhen Wang 0 Yongjun Chen 0 1 Shiwei Lin 0 1 0 College of Materials and Chemical Engineering, Hainan University , Haikou 570228 , People's Republic of China 1 State Key Laboratory of Marine Resource Utilization in South China Sea, Hainan University , Haikou 570228 , People's Republic of China Although CdS and PbS quantum dot-sensitized TiO2 nanotube arrays (TNTAs/QDs) show photocatalytic activity in the visible-light region, the low internal quantum efficiency and the slow interfacial hole transfer rate limit their applications. This work modified the surface of the TNTAs/QDs photoelectrodes with metal-oxide overlayers by atomic layer deposition (ALD), such as coating Al2O3, TiO2, and ZnO. The ALD deposition of all these overlayers can apparently enhance the photoelectrochemical performance of the TNTAs/QDs. Under simulated solar illumination, the maximum photocurrent densities of the TNTAs/QDs with 10 cycles ZnO, 25 cycles TiO2, and 30 cycles Al2O3 overlayers are 5.0, 4.3, and 5.6 mA/cm2 at 1.0 V (vs. SCE), respectively. The photoelectrode with Al2O3 overlayer coating presents the superior performance, whose photocurrent density is 37 times and 1.6 times higher than those of the TNTAs and TNTAs/QDs, respectively. Systematic examination of the effects of various metal-oxide overlayers on the photoelectrochemical performance indicates that the enhancement by TiO2 and ZnO overcoatings can only ascribed to the decrease of the interfacial charge transfer impedance, besides which Al2O3 coating can passivate the surface states and facilitate the charge transfer kinetics. These results could be helpful to develop high-performance photoelectrodes in the photoelectrochemical applications. TiO2 nanotube arrays; Quantum dots; Surface modification; Atomic layer deposition; Photoelectrochemical performance - Background TiO2 is a kind of inorganic semiconductor materials with excellent photocatalytic activity, non-toxicity, and good stability. It is widely used in the fields of water splitting, photocatalysis, solar cells, lithium ion battery, etc. In 1972, Honda and Fujishima have achieved water splitting using TiO2 photoanode under xenon lamp irradiation [1]. Different architectures of TiO2 nanomaterials have been fabricated, such as nanoparticles [2], nanowires [3], nanotubes [4], nanosheets [5], nanoflowers [6], hollow spheres [7] etc. Especially the nanotube arrays have been widely studied with excellent optical excitation and charge transfer properties. However, TiO2 cannot effectively use the visible light because of its wide bandgap (?3.2 eV). Transition metals [8] or nonmetals [9] doping can reduce the bandgap of TiO2, but the dopants can easily become the electron-hole recombination centers [10]. The other method is using narrow-bandgap materials such as quantum dots (QDs) to sensitize TiO2 and enhance their photocatalytic activity in the visible-light region since the photogenerated charge can quickly separate and transfer between different semiconductors [11, 12]. CdS [13], CdSe [14], PbS [15], and PbSe [16] quantum dots can respond to the visible light with a tunable bandgap [17]. In recent years, co-sensitized TiO2 with quantum dots such as CdSe/ CdTe [18], CdS/CdSe [19], and PbS/CdS [20] have been reported. However, the efficiency of quantum dotsensitized TiO2 photoelectrodes is still at a lower level. ? The Author(s). 2017 Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The main reasons are the serious optical etching and the large number of defects in the surface of the quantum dots which will lead to the formation of charge recombination centers. Surface modification by atomic layer deposition (ALD) is an advanced method to prepare metal-oxide layers on the electrodes to improve their performance. Al2O3, TiO2, and ZnO are three kinds of common metal oxides which could be prepared by ALD for surface modification. The process is that two precursors are separately introduced into the reaction chamber by alternation pulse, and the chemical adsorption and surface reaction will occur on the sample [21]. Compared with traditional deposition methods, ALD can prepare uniform and controllable thin film. Metal oxides prepared by ALD technique have been used to passivate surface defects of semiconductor materials in the fields of photocatalysis and water splitting. For photoelectrochemical water splitting, ALD technique has been employed and showed promising results for Al2O3/TiO2 [22], TiO2/TiO2 nanorod arrays [23], ZnO/TiO2 [24, 25], and Co3O4/TiO2 [26]. In the previous reports, however, such metal-oxide layers were mostly used as an energy barrier between quantum dots sensitizer and semiconductor electrodes to suppress charge recombination and improve the incorporated amounts of QDs. There are still few systematic studies on the effects of metal-oxide overlayers on the photoelectrochemical performance of the QDsensitized photoelectrodes, and even no comprehensive comparison of Al2O3, TiO2, and ZnO has been reported so far. However, such information is not only significant to understand the various underlying mechanisms of the different overcoatings but also valuable for proper selection of metal-oxide overlayer to improve the photoelectric properties and for rational design and optimization of high-performance photoelectrodes. We report here the improving photoelectrochemical performance of quantum dot-co-sensitized TiO2 nanotube arrays through surface modification by ALD coating various metal-oxide overlayers. The CdS and PbS quantum dot-co-sensitized TNTA photoelectrode shows a significant enhancement in the visible-light absorption range between 400 and 600 nm. Three kinds of metaloxide overlayers, Al2O3, TiO2, and ZnO, have been uniformly coated throughout the surface of the photoelectrodes by ALD. Their photoelectrochemical performance has been studied by linear sweep voltammetry, electrochemical impedance spectroscopy, and Mott-Schottky analysis. The systematic examination of the role of various metal-oxide overlayers reveals the underlying mechanism of the enhancement. The results show that ALD deposition of metal-oxide overlayers is a promising and facile method to improve the photoelectric properties of the semiconductor electrodes. Methods Preparation of TiO2 Nanotube Arrays Prior to electrochemical anodization, Ti foils with a thickness of 0.5 mm and purity of 99.5% were chemical polished and ultrasonically cleaned in acetone, ethanol, and deionized water (DI) for 15 min successively. TNTAs were prepared by anodic oxidation method in a two-electrode system with titanium plates as working electrode and stainless steel sheet as counter electrode. The electrolyte was 0.27 M NH4F solution, and the solvent was a mixture of glycerin and DI water with the volume ratio of 1:1. The anodic oxidation was conducted at a biased of 25 V for 5 h at room temperature [27]. After the oxidation, the TNTAs obtained were soaked in ethanol for 3 min ultrasonic cleaning in order to remove the white floc surface. In order to convert amorphous structures to the crystalline phase, the samples were annealed at 450 ?C for 3 h and 45 min with a heating rate of 2 ?C/ min, and then heat cooled to room temperature in the furnace. Preparation of CdS/PbS Co-sensitized TiO2 Nanotube Arrays PbS and CdS quantum dots were loaded over crystallized TiO2 nanotube arrays by the successive ionic layer adsorption and reaction (SILAR) method. The specific steps are as follows: The precursor solutions were 0.02 M Pb (NO3)2 methanol solution and 0.02 M Na2S solution of methanol and deionized water (V:V = 1:1). TNTAs were first dipped in 0.02 M Pb (NO3)2 methanol solution for 15 s, and then keep for 1 min 45 s, rinsed with methanol, dipped in 0.02 M Na2S solution for 15 s, and then keep for 1 min 45 s rinsed with methanol; two procedures were termed as one deposition cycle of PbS quantum dots and then repeated 5 times. Secondly, the samples were sensitized with CdS quantum dots immediately. Similar to the procedure above, the deposition cycles of CdS quantum dots were 5 as well. The precursor solutions were 0.05 M Cd (NO3)2 ethanol solution and 0.05 M Na2S solution (volume ratio of methanol and DI water is 1:1). The sample is referred to as TNTAs/QDs [28]. Finally, the sample was covered with 2 cycles ZnS protecting layer to reduce surface recombination [28, 29]. Preparation of TiO2 Co-sensitized CdS/PbS Nanotube Arrays Modified by ALD Metal Oxide Overlayers ALD method was then applied for metal-oxide overlayer coating. In order to guarantee that the photogenerated electrons can tunnel through the overlayer and the results are comparable, the overlayer thickness is kept about 1.5 nm. This requires the overlayer deposition with 30 cycles Al2O3 (0.5 ?/cycle), 25 cycles TiO2 (0.6 ?/cycle), and 10 cycles ZnO (1.5 ?/cycle), respectively. The precursor was dissolved in 1 M heptane in solution, the reactor temperature is 150 ?C, and N2 as carrier gas and washing gas. For Al2O3 deposition, three methyl aluminum (trimethylaluminum, TMA) was used as precursor. The specific steps are as follows. TNTAs/QDs samples were first put in the chamber. An ALD cycle of Al2O3 deposition consisted of a 0.02 s pulse of TMA, 5 s exposure to TMA, 15 s purge with N2 and then 0.05 s pulse of H2O, 5 s exposure to H2O, final 15 s purge with N2, thus completing a cycle of Al2O3 deposition [30]. An ALD cycle of TiO2 deposition and ZnO deposition were similar to the above procedures but selected diethyl zinc (DEZ) and titanium (IV) isopropoxide as their precursors, respectively [31]. In order to minimize the effect of surface area variation, we carefully controlled the process condition for preparing the quantum dot-sensitized TiO2 nanotube arrays and kept the thickness of the passivation layer deposited as about 1.5 nm. Characterization and Photoelectrochemical Performance Testing The surface morphology and microstructure of the samples were observed by using scanning electron microscopy (FESEM, Hitachi, S4800) and transmission electron microscopy (TEM, JEM 2100). Energy dispersive X-ray spectrometer (EDS) accompanying FESEM was used to analyze sample element. X-ray diffraction (XRD, Bruker D8) with Cu Ka radiation was used to analyze the crystal structure of the samples. The optical absorption properties of the samples were recorded by UV-Vis spectrophotometer (UV, Purkinje TU-1901). The photoelectric properties of the samples were tested by electrochemical workstation (Zennium Zahner) in a standard three-electrode setup with the prepared sample as the working electrode with a specific exposure area of 1 cm2. A double salt bridge saturated calomel electrode (SCE) and a Pt wire were the reference and the counter electrodes, respectively. The electrolyte was a aqueous solution mixed with 0.1 M Na2S and 0.2 M Na2SO3 with a volume ratio of 1:1 (pH = 12.2). The voltage scan rate of linear sweep voltammetry (LSV) test was 10 mV/s, and the excitation light source was a 500 W xenon lamp with the wavelength range from 350 to 1100 nm and calibrated through an AM 1.5 filter and PC-2 solar radiation recorder (AM 1.5G, 100 mW/cm2). LED lamp was used as the excitation light source of the transient photocurrent test with electrochemical workstation (wavelength 565 + 112 nm; light intensity 80 mW/cm2), while every 25 s for a range of switch lamp to achieve light and dark conditions. Electrochemical impedance spectroscopy (EIS) was examined under open-circuit voltage and simulated solar light condition. The amplitude was 10 mV and the frequency range was from 0.1 Hz to 100 KHz. MottSchottky analysis was performed in the dark condition, and the voltage range is from ?1 to 0.9 V. The scanning rate was 30 mV/s, and the frequency and amplitude perturbation were 1 kHz and 10 mV. Results and Discussion Figure 1 depicts the quantum dot-sensitized TiO2 nanotube arrays with different metal oxide overlayers. The structure of TiO2 nanotube arrays is highly ordered on Ti foils with smooth surface and an average tube inner diameter of 110 nm as shown in Fig. 1a. The inset in Fig. 1a is a cross-sectional view of the quantum dotsensitized TiO2 nanotube arrays. The length of the nanotubes is about 1.7 ?m and the wall thickness is about 23 nm. The size of the quantum dots is too small to be observed by SEM. The inner diameters of TiO2 nanotubes decrease after oxide layer coating by ALD (Fig. 1b?d), indicating conformal overlayer deposition along the high-aspect ratio nanotubes. Figure 2 is the high-resolution TEM (HRTEM) images of the TNTAs/QDs both before and after the metaloxide layer deposition. The illustration in the insets is the corresponding low-resolution TEM images. It can be seen that the quantum dots are evenly distributed on the TiO2 nanotubes with a particle size of approximately 8 nm. It can be seen from Fig. 2b?d that a smooth, uniform, and light-color layer with thickness of approximately 1.5 ? 0.5 nm is wrapped outside the TNTAs/QDs. The thin layer are Al2O3, ZnO, and TiO2 coating, respectively. In Fig. 2a, the spacing of 3.29 and 3.58 ?, respectively, correspond to the (111) lattice plane of the cubic phase CdS (JCPDS No. 89-0440) and the (101) lattice plane of the TiO2 anatase type (JCPDS 21-1272); in Fig. 2d, the lattice spacing of 2.97 ? correspond to the (200) lattice plane of the cubic phase PbS. In order to determine the crystal structure, the TNTAs/QDs, TNTAs/QDs/10 cycles ZnO, TNTAs/ QDs/25 cycles TiO2, TNTAs/QDs/30 cycles Al2O3, electrodes were characterized by XRD, as shown in Fig. 3. The XRD pattern with the deposited passivation layers on the TNTAs/QDs is substantially coincidental, indicating that the passivation layers cannot change the crystal structure of the electrode. The peak of the corresponding oxides cannot be founded in the XRD patterns, but the previous TEM images in Fig. 2 and the EDS result shown in Fig. 4 support the presence of the oxide overlayer. This indicates amorphous structure of metal-oxide overlayer Fig. 1 SEM images of TNTAs/QDs with various ALD cycles overlayer: a 0 cycles, b 30 cycles Al2O3, c 10 cycles ZnO, and d 25 cycles TiO2. The inset in a is a cross-sectional view of the well-aligned quantum dot-sensitized TiO2 nanotube arrays without any overlayer prepared by ALD. The diffraction peaks at 25.4?, 37.2?, 48.1?, 54.1?, and 55.2? correspond to the (101), (004), (200), (105), and (211) lattice planes of the TiO2 anatase phase (JCPDS No. 21-1272), respectively. The diffraction peaks of CdS, PbS, and ZnS are practically invisible in the four samples, most likely because the amount of the quantum dots are less than the XRD detection limitation. The EDS pattern in Fig. 4 shows that Ti, O, Cd, Pb, Zn, and S elements are present in these four samples, indicating the presence of the CdS and PbS quantum dots on TNTAs. In addition, the Al element can be found in the pattern of the TNTAs/QDs/30 cycles Al2O3 sample. The atomic percentage of the Zn element in TNTAs/ QDs/10 cycles ZnO is much greater than that of the other three samples, and the atomic percentage of the Ti Fig. 2 TEM images of TNTAs/QDs with various ALD cycles overlayer: a 0 cycles, b 30 cycles Al2O3, c 10 cycles ZnO, and d 25 cycles TiO2. The insets are the corresponding low-resolution TEM images Fig. 3 XRD patterns of the TNTAs/QDs, TNTAs/QDs/10 cycles ZnO, TNTAs/QDs/25 cycles TiO2, and TNTAs/QDs/30 cycles Al2O3 electrodes element in the TNTAs/QDs/25 cycles TiO2 is also greater than that of the other three samples. These further suggest the presence of the passivation layers. The Na element in the TNTA/QD pattern may come from the precursor Na2S solution used in the preparation of the quantum dots. Atomic percentages of the elements derived from the EDS spectra are summarized in Table 1. The UV-vis diffuse reflectance absorption spectra were characterized on these photoelectrodes, as shown in Fig. 5. The bandgap of the anatase type TiO2 is 3.2 eV, well corresponding to the absorption band edge measured at approximately 380 nm for the pure TNTAs. In contrast, the CdS and PbS quantum dot-co-sensitized TNTA photoelectrode shows a significant enhancement in a visible-light absorption range especially between 400 and 600 nm. The bandgap of CdS is 2.4 eV, which can only absorb light with wavelength less than 520 nm. After co-sensitization with PbS quantum dot, which has smaller bandgap (~0.4 eV), the absorption range can Fig. 4 EDS results of the TNTAs/QDs, TNTAs/QDs/10 cycles ZnO, TNTAs/QDs/25 cycles TiO2, and TNTAs/QDs/30 cycles Al2O3 electrodes 30 cycles Al2O3 [%] 55.36 25 cycles TiO2 [%] extend beyond 700 nm in the solar spectrum. At the same time, it is found that the deposition of the metal oxides on the TNTAs/QDs does not obviously change the light absorption properties, which suggests that the enhancement of the PEC performance observed later is not caused by the increase of the absorption of light by the passivation layer, similar to the results reported in other papers [32]. The photoelectrochemical performance of the photoelectrodes with different cycle metal oxide passivation layers deposited on the TNTAs/QDs is shown in Fig. 6. Figure 6a is the LSV plots of the four electrodes, which is made negligible since the dark current density of all of the samples is less than 200 ?A, which is negligible. Under the simulated solar irradiation, the photocurrent density of the pure TNTAs is 0.14 mA/cm2 at 1 V (vs. SCE). After quantum dot sensitization, the photocurrent density increases to 3.48 mA/cm2 under the same bias, which is 23 times higher than the photocurrent density of the unsensitized electrode. Under simulated solar illumination, the maximal photocurrent density of 10 cycles ZnO, 25 cycles TiO2, and 30 cycles Al2O3 overlayer coating on the TNTAs/QDs are 5.0, 4.3, and 5.6 mA/ cm2, respectively. In comparison, photocurrent density of TNTAs/QDs/30 cycles Al2O3 is relatively maximal, which is 37 times higher than the photocurrent density of the TNTAs, and 1.6 times higher than the TNTAs/ QDs. With the exception of TNTAs, the starting potentials of the photocurrent in all the samples are about ?1.0 V (vs. SCE), indicating that the conduction band edge basically remains fixed. The photoconversion efficiency of each electrode under different bias voltages is shown in Fig. 6b. The maximum photoconversion efficiencies of the TNTAs, TNTAs/QDs, TNTAs/QDs/10 cycles ZnO, TNTAs/ QDs/25 cycles TiO2, and TNTAs/QDs/30 cycles Al2O3 electrodes are 0.06, 2.57, 3.95, 3.41, and 4.23% respectively. Thus, deposition of the metal-oxide layers onto the TNTA/QD photoelectrode can apparently increase their photoconversion efficiency. The efficiency of TNTAs/QDs/30 cycles Al2O3 is 1.6 times as much as TNTAs/QDs, better than the other photoelectrode. Compared with the TNTAs, the photoconversion efficiency could be maximally increased by 41 times after QDs co-sensitization and metal-oxide overlayer deposition. Figure 6c presents the transient light response of the TNTA/QD electrodes with different ALD overlayers under the white-light excitation with the density of 80 mW/cm2 and the wavelength range of 565 ? 112 nm. The photocurrent of the four samples increased rapidly with the switching on of the LED lamp, which indicates that the photogenerated electrons in the electrode can rapidly be excited and injected into the TNTAs from the quantum dots. The photocurrent density of each Fig. 5 UV-vis absorption spectra of the pure TNTAs, TNTAs/QDs, TNTAs/QDs/10 cycles ZnO, TNTAs/QDs/25 cycles TiO2, and TNTAs/QDs/30 cycles Al2O3 electrodes Fig. 6 PEC properties of the TNTAs/QDs, TNTAs/QDs/10 cycles ZnO, TNTAs/QDs/25 cycles TiO2, and TNTAs/QDs/30 cycles Al2O3 electrodes with a surface area of 1 cm2. a LSV curves of the electrodes under simulated solar illumination. b Photoconversion efficiency derived from LSV curves. c Transient photoresponse under chopped light irradiation under a potential 0 V vs. SCE electrode recorded after the five switch lamp cycles shows no significant decrease which suggests the stability of the electrodes. The effects of the passivation layer on the photoelectric properties can be summarized as follows: (1) to passivate the surface defects of the TNTAs/quantum dots, (2) to play a catalytic effect in order to promote charge transfer, (3) to build a heterojunction to reduce the interface impedance. In order to clarify the underlying mechanism, these photoelectrodes were examined by EIS and Mott-Schottky measurements [30], and the results are shown in Fig. 7. EIS results in Fig. 7a qualitatively demonstrate the charge transfer properties of the photoelectrodes with and without oxide passivation layer. The interfacial charge transfer impedance is inversely proportional to the arc diameters in the Nyquist plots. Among the four photoelectrodes, the interfacial charge transfer impedance increases as the following trend: TNTAs/QDs/ 30 cycles Al2O3, TNTAs/QDs/10 cycles ZnO, TNTAs/ QDs/25 cycles TiO2, and TNTAs/QDs. It can be seen that all the oxide layers can reduce the interfacial charge transfer impedance, which will accelerate the carrier separation and transmission and then improve the photoelectrochemical performance. From the Mott-Schottky measurements in Fig. 7b, the carrier concentrations of the TNTAs/QDs, TNTAs/QDs/10 cycles ZnO, and TNTAs/QDs/25 cycles TiO2 electrodes could be calculated as 3.36 ? 1019 cm?3, while the TNTAs/QDs/30 cycles Al2O3 electrode is 1.32 ? 1020 cm?3. The charge carriers are generated in a semiconductor by the irradiation with light energy larger than its bandgap. There Fig. 7 a EIS spectra of the TNTAs/QDs, TNTAs/QDs/10 cycles ZnO, TNTAs/QDs/25 cycles TiO2, and TNTAs/QDs/30 cycles Al2O3 electrodes. b Mott-Schottky analysis of the TNTAs/QDs, TNTAs/QDs/10 cycles ZnO, TNTAs/QDs/25 cycles TiO2, and TNTAs/QDs/30 cycles Al2O3 electrodes are a large number of defects on the surface of the TNTA/QD electrode. These defects work as recombination centers, leading to a decrease in carrier concentration. The Al2O3 layer coating on the surface of quantum dots plays a key role to passivate the surface defects and reduce charge recombination. Thus, Al2O3 coating can be found to increase the effective carrier concentration. In addition, when the electrode deposited with the Al2O3 passivation layer is exposed to light, the photogenerated holes in the valence band are rapidly injected from the quantum dots into the quantum dot/Al2O3 interface under the built-in electric field. Moreover, the negative charge in the Al2O3 layer would form a built-in electric field which can prevent the photogenerated electrons inside the bulk material, thus effectively reduce the recombination of photogenerated charges [30]. Although the surface passivation effect on TiO2 nanorod arrays with TiO2 coating were reported in the literature [23], according to our Mott-Schottky results, the carrier concentrations of the TNTA/QD electrode with TiO2 and ZnO coating keep the same as that of the TNTAs/QDs electrode, indicates that TiO2 and ZnO overlayers can hardly passivate the surface defects of the TNTAs/QDs electrode. The enhancement by TiO2 and ZnO overcoating is mainly due to the reduction of the interfacial charge transfer impedance. The photochemical stability of the photoanodes is another important concern. After a series of electrochemical performance tests (transient photocurrent, LSV, and EIS tests) under illumination, there were no evident changes in photoelectrochemical performance for the three samples. But under 2 h continuous illumination, the photocurrent density of the photoelectrode with 30 cycles Al2O3 decayed slowly while that of the bare electrode suffered serious decay. This is because Al2O3 oxide layer has been partially dissolved in the electrolyte (a mixed solution of Na2SO3 and Na2S, used to prevent the oxidation of sulfide ions), leading to decrease of the transformation of photogenerated electrons and holes. The photochemical stability of the photoelectrodes with the ZnO and TiO2 overlayers shows similar decay to that with Al2O3, which is possibly due to their similar amorphous nature. In terms of long-term photochemical stability, future work is required to understand the underlying reason and to optimize the overlayer by improving the crystallinity or combining different oxide layers by ALD. Conclusions ALD technology has been applied to deposit various uniform and compact oxide overlayers, Al2O3, TiO2, and ZnO with controllable thickness, on the TNTAs/QDs structure. These overlayers within the tunneling thickness of approximately 1.5 nm can enhance the photoelectric properties of the TNTA/QD photoelectrodes. Under simulated sunlight, the maximal photocurrent densities of the TNTAs/QDs with 10 cycles ZnO, 25 cycles TiO2, and 30 cycles Al2O3 overlayers are 5.0, 4.3, and 5.6 mA/cm2, respectively. All the three oxide overcoating can improve the photoelectrochemical performance of the TNTAs/QDs, but the underlying mechanisms are different. Al2O3 overlayer can chemically passivate the surface defects of the TNTA/QDs electrode, reduce the charge recombination, and improve the transfer efficiency of the charge in the bulk material and the transfer kinetics at the interface. This leads to the superior performance than TiO2 and ZnO overlayers, which just reduce the interfacial charge transfer impedance in varying degrees without increasing the carrier concentration. This work demonstrates that the proper selection of metal-oxide overlayer is of great importance to improve the photoelectric properties, and the ALD technology is a promising and facile method for surface modification to prepare the high-performance electrodes in the photoelectrochemical applications. Authors? Contributions QZ designed and conducted the experiments and analyses and drafted the manuscript. JZ and MZ provided the technical support and conceptual advice. GW and YC participated in the design of the study. SL conceived the idea and modified the manuscript. All authors read and approved the final manuscript. 1. Fujishima A , Honda K ( 1972 ) TiO2 photoelectrochemistry and photocatalysis . Nature 238 : 37 - 38 2. Burnside SD , Shklover V , Barb? C , Comte P , Arendse F , Brooks K , Gr?tzel M ( 1998 ) Self-organization of TiO2 nanoparticles in thin films . Chem Mater 10 : 2419 - 2425 3. Lin Y , Wu GS , Yuan XY , Xie T , Zhang LD ( 2003 ) Fabrication and optical properties of TiO2 nanowire arrays made by sol-gel electrophoresis deposition into anodic alumina membranes . J Phys Condens Matter 15 : 2917 4. Zhu K , Neale NR , Miedaner A , Frank AJ ( 2007 ) Enhanced charge-collection efficiencies and light scattering in dye-sensitized solar cells using oriented TiO2 nanotubes arrays . Nano Lett 7 : 69 - 74 5. Yu J , Qi L , Jaroniec M ( 2010 ) Hydrogen production by photocatalytic water splitting over Pt/TiO2 nanosheets with exposed (001) facets . J Phys Chem C 114 : 13118 - 13125 6. Zhang M , Shao C , Guo Z , Zhang Z , Mu J , Cao T , Liu Y ( 2011 ) Hierarchical nanostructures of copper (II) phthalocyanine on electrospun TiO2 nanofibers: controllable solvothermal-fabrication and enhanced visible photocatalytic properties . ACS Appl Mater Interfaces 3 : 369 - 377 7. Xuan S , Jiang W , Gong X , Hu Y , Chen Z ( 2008 ) Magnetically separable Fe3O4/TiO2 hollow spheres: fabrication and photocatalytic activity . J Phys Chem C 113 : 553 - 558 8. Martins PM , Gomez V , Lopes AC , Tavares CJ , Botelho G , Irusta S , LancerosMendez S ( 2014 ) Improving photocatalytic performance and recyclability by development of Er-doped and Er/Pr-codoped TiO2/poly (vinylidene difluoride)-trifluoroethylene composite membranes . J Phys Chem C 118 : 27944 - 27953 9. Sakthivel S , Kisch H ( 2003 ) Daylight photocatalysis by carbon-modified titanium dioxide . Angew Chem Int Ed 42 : 4908 - 4911 10. Li GS , Zhang DQ , Yu JC ( 2009 ) A new visible-light photocatalyst: CdS quantum dots embedded mesoporous TiO2 . Environ Sci Technol 43 : 7079 - 7085 11. Zhang X , Lin S , Liao J , Pan N , Li D , Cao X , Li J ( 2013 ) Uniform deposition of water-soluble CdS quantum dots on TiO2 nanotube arrays by cyclic voltammetric electrodeposition: Effectively prevent aggregation and enhance visible-light photocatalytic activity . Electrochim Acta 108 : 296 - 303 12. Hensel J , Wang G , Li Y , Zhang JZ ( 2010 ) Synergistic effect of CdSe quantum dot sensitization and nitrogen doping of TiO2 nanostructures for photoelectrochemical solar hydrogen generation . Nano Lett 10 : 478 - 483 13. Sun WT , Yu Y , Pan HY , Gao XF , Chen Q , Peng LM ( 2008 ) CdS quantum dots sensitized TiO2 nanotube-array photoelectrodes . J Am Ceram Soc 130 : 1124 - 1125 14. Lee YL , Huang BM , Chien HT ( 2008 ) Highly efficient CdSe-sensitized TiO2 photoelectrode for quantum-dot-sensitized solar cell applications . Chem Mater 20 : 6903 - 6905 15. Hoyer P , K?nenkamp R ( 1995 ) Photoconduction in porous TiO2 sensitized by PbS quantum dots . Appl Phys Lett 66 : 349 - 351 16. Pietryga JM , Schaller RD , Werder D , Stewart MH , Klimov VI , Hollingsworth JA ( 2014 ) Pushing the band gap envelope: mid-infrared emitting colloidal PbSe quantum dots . J Am Chem Soc 126 : 11752 - 11753 17. Kim JC , Choi J , Lee YB , Hong JH , Lee JI , Yang JW , Lee WI , Hur NH ( 2006 ) Enhanced photocatalytic activity in composites of TiO2 nanotubes and CdS nanoparticles . Chem Commun 48 : 5024 - 5026 18. de Mello DC , Koole R ( 2009 ) Size dependence of the spontaneous emission rate and absorption cross section of CdSe and CdTe quantum dots . J Phys Chem C 113 : 6511 - 6520 19. Lee YL , Chi CF , Liau SY ( 2009 ) CdS/CdSe co-sensitized TiO2 photoelectrode for efficient hydrogen generation in a photoelectrochemical cell? . Chem Mater 22 : 922 - 927 20. Lv P , Fu W , Mu Y , Sun H , Su S , Chen Y , Yang H ( 2015 ) Photoelectrochemical property of CdS and PbS cosensitized on the TiO2 array by novel successive ionic layer adsorption and reaction method . J Alloys Compd 621 : 30 - 34 21. George SM ( 2008 ) Atomic layer deposition: an overview . Chem Rev 110 : 111 - 131 22. Roelofs KE , Brennan TP , Dominguez JC , Bailie CD , Margulis GY , Hoke ET , Bent SF ( 2013 ) Effect of Al2O3 recombination barrier layers deposited by atomic layer deposition in solid-state CdS quantum dot-sensitized solar cells . J Phys Chem C 117 : 5584 - 5592 23. Mali SS , Shim CS , Park HK , Heo J , Patil PS , Hong CK ( 2015 ) Ultrathin atomic layer deposited TiO2 for surface passivation of hydrothermally grown 1D TiO2 nanorod arrays for efficient solid-state perovskite solar cells . Chem Mater 27 : 1541 - 1551 24. Kao MC , Chen HZ , Young SL ( 2009 ) Effects of ZnO coating on the performance of TiO2 nanostructured thin films for dye-sensitized solar cells . Appl Phys A 97 : 469 - 474 25. Lee W , Kang SH , Kim JY , Kolekar GB , Sung YE , Han SH ( 2009 ) TiO2 nanotubes with a ZnO thin energy barrier for improved current efficiency of CdSe quantum-dot-sensitized solar cells . Nanotechnology 20 : 335706 26. Huang B , Yang W , Wen Y , Shan B , Chen R ( 2014 ) Co3O4-modified TiO2 nanotube arrays via atomic layer deposition for improved visible-light photoelectrochemical performance . ACS Appl Mater Interfaces 7 : 422 - 431 27. Li D , Lin S , Li S , Huang X , Cao X , Li J ( 2012 ) Effects of geometric and crystal structures on the photoelectrical properties of highly ordered TiO2 nanotube arrays . J Mater Res 27 : 1029 - 1036 28. Zhang X , Zeng M , Zhang J , Song A , Lin S ( 2016 ) Improving photoelectrochemical performance of highly-ordered TiO2 nanotube arrays with cosensitization of PbS and CdS quantum dots . RSC Adv 6 : 8118 - 8126 29. Kim HJ , Lee HD , Kumar CSSP , Rao SS , Chung SH , Punnoose D ( 2015 ) The effect of manganese in a CdS/PbS colloidal quantum dot sensitized TiO2 solar cell to enhance its efficiency . New J Chem 39 : 4805 - 4813 30. Zeng M , Peng X , Liao J , Wang G , Li Y , Li J , Lin S ( 2016 ) Enhanced photoelectrochemical performance of quantum dot-sensitized TiO2 nanotube arrays with Al2O3 overcoating by atomic layer deposition . Phys Chem Chem Phys 18 : 17404 - 17413 31. Zeng M , Zeng X , Peng X , Zhu Z , Liao J , Liu K , Lin S ( 2016 ) Improving photoelectrochemical performance on quantum dots co-sensitized TiO2 nanotube arrays using ZnO energy barrier by atomic layer deposition . Appl Surf Sci 388 : 352 - 358 32. Hwang YJ , Hahn C , Liu B , Yang P ( 2012 ) Photoelectrochemical properties of TiO2 nanowire arrays: a study of the dependence on length and atomic layer deposition coating . ACS Nano 6 : 5060 - 5069


This is a preview of a remote PDF: https://link.springer.com/content/pdf/10.1186%2Fs11671-017-2036-6.pdf

Quan Zhou, Junchen Zhou, Min Zeng, Guizhen Wang, Yongjun Chen, Shiwei Lin. Photoelectrochemical Performance of Quantum dot-Sensitized TiO2 Nanotube Arrays: a Study of Surface Modification by Atomic Layer Deposition Coating, Nanoscale Research Letters, 2017, 261, DOI: 10.1186/s11671-017-2036-6