On the performance of the Code Division Duplex system using interference rejection codes

EURASIP Journal on Wireless Communications and Networking, Sep 2017

In this paper, we investigate the performance of the Code Division Duplex (CDD) system using the interference rejection codes, which exhibit zero correlation values on the relative delay-induced code offsets and can be applied to mitigate the mutual interference between the uplink and downlink. Specifically, we propose to employ loosely synchronous codes to effectively combat the interference through the interference-free window. Moreover, the simplified RAKE structure is proposed as the receiver of the CDD device, which can significantly reduce the complexity in the implementation. The simulation results demonstrate that our proposed method can achieve a near inference-free performance when the user load of the system is moderate.

A PDF file should load here. If you do not see its contents the file may be temporarily unavailable at the journal website or you do not have a PDF plug-in installed and enabled in your browser.

Alternatively, you can download the file locally and open with any standalone PDF reader:

https://link.springer.com/content/pdf/10.1186%2Fs13638-017-0937-9.pdf

On the performance of the Code Division Duplex system using interference rejection codes

Yin et al. EURASIP Journal on Wireless Communications and Networking On the performance of the Code Division Duplex system using interference rejection codes Yufang Yin 1 Gangjun Li 1 Li Li 0 Hua Wei 0 0 Chengdu University of Information and Technology , Chengdu , China 1 Chengdu Technological University , Chengdu , China In this paper, we investigate the performance of the Code Division Duplex (CDD) system using the interference rejection codes, which exhibit zero correlation values on the relative delay-induced code offsets and can be applied to mitigate the mutual interference between the uplink and downlink. Specifically, we propose to employ loosely synchronous codes to effectively combat the interference through the interference-free window. Moreover, the simplified RAKE structure is proposed as the receiver of the CDD device, which can significantly reduce the complexity in the implementation. The simulation results demonstrate that our proposed method can achieve a near inference-free performance when the user load of the system is moderate. 1 Introduction A duplex communication system [ 1 ] is a point-to-point system composed of two connected parties or devices that can communicate with one another in both directions, normally termed as uplink and downlink individually. To circumvent the mutual interference between the uplink and downlink, the Frequency Division Duplex (FDD) [ 1 ] and Time Division Duplex (TDD) [ 1 ] apparatuses are commonly deployed in communication systems. In the FDD system, the uplink and downlink signals are gapped in different frequency bands, while in the TDD system, the uplink and downlink transmissions are identified in different time slots. In this way, the uplink and downlink can be treated as being orthogonal in the FDD or TDD apparatus since they utilize different frequency or time resources. Recently, No Division Duplex (NDD) [ 2, 3 ] techniques have captured growing interests for the 5G communication system, since they can significantly increase the capacity of the cellular system as well as simplify the infrastructure of the cellular network. The basic philosophy of the No Division Duplex [ 2, 3 ] is that a radio device can transmit and receive on the same frequency at the same time; more explicitly, it can operate in a fullduplex fashion. However, as the radio signals attenuate quickly in an exponential way over the distance, the signal from a local transmitting antenna is hundreds of thousands of times stronger than transmissions from other nodes. Therefore, the challenge in implementing a fullduplex system is to recover the desired signal from the excessively strong local interferers. Hence, a complicated interference canceller [ 3 ] must be deployed in the NDD device to combat the local interference, in both the analog RF component as well as the digital baseband component. In Code Division Multiple Access (CDMA) systems, the spreading sequences characterize the properties of the associated Intersymbol Interference (ISI) as well as the Multiple Access Interference (MAI) [ 4 ]. Traditional spreading sequences, such as m-sequences [ 4 ], Gold codes [ 4 ], and Kasami codes [ 4 ], exhibit non-zero off-peak autocorrelations and cross-correlations, which result in a high MAI in the system. To circumvent this issue, the ideal solution is to design the optimal sequences whose autoand cross-correlations are zero for the infinite code offsets, as shown in Fig. 1a. However, this kind of perfect sequence does not exist in theory. Therefore, considerable research has been invested on the interference rejection code which can exhibit zero correlation values on the relative delay-induced code offsets. The area which has the value of zero correlation is the so-called Zero Correlation Zone (ZCZ) or Interference-Free Window (IFW) of the spreading code [ 5 ], as shown in Fig. 1d. The auto- and cross-correlation properties of four spreading codes are exhibited in Fig. 1. In this figure, we can observe that the correlation value of the interference rejection code is zero in IFW. Loosely Synchronous (LS) code [ 6, 7 ] is one of these specific interference rejection codes which exhibit an IFW, where the off-peak values of aperiodic auto- and cross-correlations are zero, resulting in zero ISI and zero MAI in the IFW. Given these conditions, a major benefit of the interference rejection codes is that they are capable of combating the mutual interference between the uplink and downlink without a complicated interference canceller. Hanzo, Wei, and Ni [ 8–10 ] investigated the performance of the CDMA system in the context of the deployment the LS codes. However, in their work, the power control [11] scheme is employed to avoid the nearfar effect, and only the cellar communication scenarios are evaluated in previous work. In [ 9, 12 ], the interference rejection codes are deployed in the multi-carrier CDMA system and the performance is analyzed. The authors in [13] investigated the performance of the CDMA system in conjunction with the multiple antenna technique and the interference rejection code. Various chip waveforms [ 14 ] are investigated for the LS codes, and the network capacity in the cellular scenario is analyzed in [ 15 ]. In this paper, to circumvent the implementation of complicated interference canceller, Code Division Duplex (CDD) is proposed for a synchronous communication system. As shown in Fig. 2, the basic concept of the CDD is that the downlink and uplink signals are distinguished by their unique spread sequence Ci, i.e., the CDD radio can transmit and receive simultaneously at the same frequency band with different spreading signatures. The state of the art CDD device can operate in the same fashion as the NDD device. However, the advantage of the CDD receiver is to employ a simple matched filter or RAKE receiver rather than a complicated interference canceller in the NDD device owing to the cross-correlation properties of the interference rejection code, which is beneficial in the engineering implementation and power saving. In this paper, we will investigate the performance of CDD communication systems in the context of two practical scenarios. The first scenario is a cellular-like communication system, where a base station node operates as the centric node and all the other CDD nodes must communicate with the center node. In this specific scenario, the center node has a much stronger transmission power than other nodes. The second scenario is an ad hoc communication system where each CDD device transmits on the same power in the network and can communicate with each other. In this contribution, we will investigate the Bit Error Rate (BER) performance and capacity of CDD systems in both scenarios when communicating over a Nakagami-m channel. This paper is organized as follows. In Section 2, we will introduce the specific interference rejection code, namely LS code, while in Section 3, we will describe the model Fig. 2 Code Division Duplex system of the CDD system and fading channel. In Section 4, we will characterize the BER performance of the CDD communication, and in Section 5, we will discuss our findings. Finally, in Section 6, we will offer our conclusion. 2 Interference rejection codes There exists a specific family of spreading codes, which exhibit an IFW; more specifically, Loosely Synchronized (LS) codes [ 6 ] exploit the properties of the so-called orthogonal complementary sets [ 6, 7 ]. Since the detailed construction method of binary LS codes was described in [ 6, 9, 10 ], here, we only focus our attention on the properties and the applications of the LS codes [ 16, 17 ]. Generally, an LS code can be denoted as LS(N , P, W0), which denotes the family of LS codes generated by applying a (P × P)-dimensional Walsh-Hadamard (WH) matrix to an orthogonal complementary code set of length N and inserting W0 number of zeros between two orthogonal complementary sets [ 6, 9, 10 ]. The constructed LS(N , P, W0) codes can be constructed for any arbitrary length of the codes by selecting the proper parameter N, and then, the generated LS codes can exhibit an IFW of interference rejection code as shown in Fig. 1; more explicitly, the spreading signature function ci(t), cj(t) of the constructed LS codes satisfy: −∞ −∞ ci(t)cj(t − τ )dt = 0, τ < WI , i = j (1) where ci(t) and cj(t) are the signature functions in the generated LS(N , P, W0) code set and WI is the width of the IFW. More explicitly, the constructed LS(N , P, W0) codes are still orthogonal to each other even in the scenarios of the multipath environment provided that the delay spread of the multipath is less than the width of IFW. Hence, the LS code with inherent IFW can effectively suppress the Multipath Interference (MPI) and multiuser access interference (MAI), which also significantly simplify the design of receiver as well as reduce the complexity of the receiver in CDMA system. For example, the LS(N , P, W0) codes can be generated based on the complementary pair of [ 6, 16 ], and the total number of available codes in the family of LS(N , P, W0) is given by NP. The total number of NP codes can be classified by N sets of P number of LS codes through their Walsh-Hadamard Matrix, and each set has P number of LS codes. The LS codes in the same set exhibit an IFW length of [−WI , +WI ], where we have WI = min{W0, N − 1}. The aperiodic auto-correlation and cross-correlation function ρkk(τ ), ρjk(τ ) of the codes belonging to the same set will be zero, provided that we have τ ≤ WI Tc. Furthermore, the LS codes belonging to the N different sets are still orthogonal to each other at zero offset, namely in a perfectly synchronous environment. However, the LS codes belonging to the N different sets will lose their orthogonality, when they have a non-zero code offset. To combat the interference incurred by its own transmission, the spreading codes in the CDD device have the following assignment policy: the spreading codes of the uplink and downlink are wisely chosen to belong to different sets of Walsh-Hadamard. The benefit of this assignment is that the spreading codes between the uplink and downlink have the maximum width of the IFW, which can guarantee the orthogonality between the uplink and downlink in one CDD node so that their mutual interference can be negligible. 3 System model 3.1 System model Assume that the system supports K synchronous users and each user is assigned two unique spreading signature waveforms for its uplink and downlink, respectively. The spreading signature waveform can be noted as ck(t) = G−1 ckiψTc (t − iTc), where G is the spreading gain and i=0 ψTc (t) is the rectangular chip waveform, which is defined over the interval [ 0, Tc). Consequently, when the K users’ signals are transmitted over the frequency-selective fading channel, the complex low-pass equivalent signal received at a given RX antenna can be expressed as: R(t) = 2Pkck(t − lTc − τk)bk(t − lTc − τk) where N (t) is the complex-valued low-pass-equivalent AWGN (additive white Gaussian noise) having a doublesided spectral density of N0 and τk is the propagation delay between the transmitter and receiver for user k. In the same CDD device, τk is assumed to be 0, while in different CDD devices, τk is determined by the propagation distance: without loss of generality, τk = dck , where c is the speed of light. Lp is the total number of resolvable paths. Pk is the received power, which is determined by the large-scale fading of the wireless channel. 3.2 Wireless large-scale fading model The complexity of wireless signal propagation makes it difficult to obtain a single model that characterizes path loss accurately across a range of different environments. In the textbook [ 1 ], various propagation models of the wireless channel are proposed and investigated in wireless communications, such as the well-known free-space channel model, Okumura Model [ 1 ], Hata Model [ 18 ], and COST207 [ 1, 18 ] which are traditionally used in system analysis. However, for the convenience of analysis of various system performance, we simplify the channel model as well as capture the essence of signal propagation without resorting to complicated path loss models, which is sufficiently accurate to approximate the real channel model. In this contribution, the following simplified models [1] for path loss as a function of distance are commonly used for system design: Pr = PtGa d d0 −γ , where d0 is the wavelength of the radio signal, d is the distance between the transmitter and receiver, and Ga is the constant which is related to the characteristic of the antenna, such as the height and direction. Parameter γ is the exponential attenuation factor which is related to the practical environment. Generally, the attenuation factor γ is about 2 to 4 according to the free-space, indoor, urban, or hilly environments. 3.3 Channel model The DS-CDMA signal experiences independent frequency-selective Nakagami-m fading. The complex low-pass equivalent representation of the Channel Impulse Response (CIR) encountered by the kth user is given by [ 19 ]: Lp−1 l=0 hk(t) = hklδ(t − lTc) exp jθkl , where hkl represents the Nakagami-distributed fading envelope, lTc is the relative delay of the lth path of user k with respect to the main path, while Lp is the total number of resolvable multipath components. Furthermore, θkl is the uniformly distributed phase-shift of the lth multipath component of the channel and δ(t) is the Kronecker delta function. More explicitly, the LP multipath attenuations {hkl} are independent Nakagami-distributed random variables with a Probability Density Function (PDF) of [ 20–22 ]: M(R, m, ) = p(hkl) = M(hkl, mkl, kl), 2mmR2m−1 (m) m e(−m/ )R2 , where (·) is the gamma function [ 19 ] and mkl is the Nakagami-m fading parameter, which characterizes the severity of the fading for the lth resolvable path of user k [ 23 ] . Specifically, mkl = 1 represents Rayleigh fading, mkl → ∞ corresponds to the conventional Gaussian scenario, and mkl = 1/2 describes the so-called one-sided Gaussian fading, i.e., the worst-case fading condition. The Rician and log-normal distributions can also be closely approximated by the Nakagami distribution in conjunction with values of mkl > 1. The parameter kl in Eq. 5 is the second moment of hkl, i.e., we have kl = E[(hkl)2]. We assume a negative exponentially decaying Multipath Intensity Profile (MIP) given by kl = k0e−ηl, η ≥ 0, l = (3) (4) (5) 0, . . . , Lp − 1, where k0 is the average signal strength corresponding to the first resolvable path and η is the rate of average power decay. 4 BER performance analysis As shown in Fig. 3, let the first user be the user of interest and consider a receiver using de-spreading as well as multipath diversity combining. The conventional matched filter-based RAKE receiver using maximum ration combining (MRC) can be invoked for detection, where we assume that the RAKE receiver combines a total of Lr number of diversity paths, which may be more or possibly less than the actual number of resolvable components at the current chip rate. It is advocated that the system has achieved perfect time synchronization and perfect estimates of the channel tap weights. Then, after appropriately delaying the outputs of the individual matched filter, in order to coherently combine the Lr number of path signals with the aid of the RAKE receiver, the output Zkl of the RAKE receiver’s lth finger sampled at t = T + lTc + τk can be expressed as: where Dkl represents the desired direct component, which can be expressed as: where TS is the symbol duration. The MRC’s decision variable Zk, which is given by the sum of all the RAKE fingers’ outputs, can be expressed as: Zkl = Dkl + Ikl, Dkl = √ 2PTsbk[0] hk2l, Zk = Zkl. Lr−1 l=0 (6) (7) (8) The RAKE fingers’ output signal Zkl is a Gaussian distributed random variable with a mean of Dkl. The term Ikl in Eq. 6 represents the total interference incurred by the Multipath Interference (MPI) as well as the Multiple Access Interference (MAI), which can be expressed as: Ikl = Ikl[S] +Ikl[M] +Nk, (9) where Ikl[S] represents the multipath interference imposed by the user of interest, which can be expressed as: Ikl[S] = 2PTshkl √ × 0 Ts lp=0 lp=l Lp−1 hklp cos θklp Ts bk t − lp −l Tc · c t − lp −l Tc c[t]dt. (10) Furthermore, Ikl[M] represents the multiuser interference inflicted by the K − 1 number of interfering signals, which can be expressed as: √ In Eqs. 10 and 11, the cos(·) terms are contributed by the phase differences between the incoming carrier and the locally generated carrier used in the demodulation. Finally, the noise term in Eq. 9 can be expressed as: Nkl = hkl n(t)c[t] cos(2π fct + θkl)dt, (12) which is a Gaussian random variable with a zero mean 2 and a variance of N0Tshkl, where {hkl} represents the path attenuations. Furthermore, Ikl[S] represents the MPI imposed by the user of interest. Without loss of generality, we can assume that the width of the IFW is longer than the channel spread time LpTc, and in this case, the MPI becomes zero since the auto-correlation of the spreading code is zero. Hence, the performance of the CDD system is mainly determined by the MAI term Ikl[M], which is affected by channel delay profile, distance amongst the nodes, and the number of users supported in a cell. Again, the uplink TX and downlink RX have different spreading sequences for the kth user in one CDD device, and recall that the system can assign different sets of the spreading codes for the uplink and downlink; more specifically, the spreading codes of the uplink and downlink have the maximum width of IFW in the generated LS codes. And the distance between the TX antenna and RX antenna is very close, i.e., τk = 0. Hence, after the matched filter and RAKE receiver, the interference introduced by its own transmission can be ignored due to the inherent orthogonality of the spreading codes. Thus, the MAI are mainly introduced by other CDD device nodes. Since the power control is difficult to be implemented in the CDD system, the near-far effect must be taken into account for the BER performance analysis. Assume that the power of the interested signals is Pk while the power of the interference is Pj, and Pk and Pj can be obtained from Eq. 3. As shown in Fig. 4, if one path of the channel impulse response of the interference user is located within the IFW, this specific path will not introduce any interference to the interested signals. More explicitly, only these paths which are located outside the interference-free window will introduce the MAI to the desired signal. Without loss of generality, we can assume that the multipath intensity profile of all users obeys the same distribution, i.e., k0 = 0, k = 1, 2, ...K , and Eb = PTs is the energy per bit. Thus, the variance of the lth RAKE finger’s output samples Zkl for a given set of channel amplitudes {hkl} may be approximated as [ 23, 24 ]: σk2l = 2PTs2 χkl 3G + 2 0Eb N0 −1 2 · 0hkl, χkl = where WI is the width of the IFW; τj and τk are the propagation delay of the interference user j and the interested user k, respectively; Lp is the total number of resolvable paths; and u(x) is the step function, i.e., u(x) = 1, x ≥ 0, otherwise u(x) = 0, x < 0. According to the largescale fading model, Pj and Pk are the strength of the received signals, which can be derived in Eq. 3 as Pj = PtjGa dd0j −γ , Pk = PtkGa ddk0 −γ . Moreover, the propagation delay obeys τj = dj/c, τk = dk/c. Hence, the MRC’s output sample Zk can be approximated by a Gaussian random variable with a mean of Hence, the BER using BPSK modulation conditioned on a set of fading attenuations {hkl, l = 0, 1, . . . , Lr − 1} can be expressed as [ 1, 18 ]: where Q(x) represents the Gaussian Q-function which can also be simplified as [ 1, 23 ]: Pb(γ ) = Q ⎝ ⎛ Furthermore, 2γl in Eq. 17 represents the output Signal to Interference plus Noise Ratio (SINR) at the lth finger of the RAKE receiver. Let us now substitute Eqs. 13, 15, and 16 into Eq. 17, and the expressions under the square-root functions must be equal, which allows us to express γl as follows: γl = χkl 3G + 0Eb N0 −1 −1 · 2 hkl . 0 For the convenience of the BER derivation, we define a term γc as: γc = χkl 3G + 0Eb N0 . With the aid of Eq. 20, we have γl = γc · (hl0)2 and hl obeys the Nakagami-m distribution characterized by Eq. 5, and the PDF of γl can be formulated as: pγl (γl) = ml γ l ml γ ml−1 mlγl (ml) exp − γ l , γl ≥ 0, (21) where γ l = γce−ηl for l = 0, 1, . . . , Lr − 1. The average BER, Pb(E), can be obtained by the weighted averaging of the conditional BER expression of Eqs. 17 and 21 over the joint PDF of the instantaneous SNR values. 5 Simulation performance of CDD As we mentioned before, two scenarios are investigated in this paper. The first scenario is a cellular system which has a center node, and all other nodes besides the center node only communicate with the center one. The second scenario is a relay and ad hoc communication environment, Lr−1 l=0 where any two of the nodes can communicate with each other. For the CDD performance evaluation, we assume that the system has a chip rate of 1.2288 M chips which is the same as the CDMA2000 and EVDO systems [ 25 ]. The bandwidth of our system is 1.25 MHz. The carrier frequency of the system is fc = 2 GHz, and the large-scale fading factor γ = 2.5. Moreover, the radius of a cell is configured to 2000 m. All the CDD nodes are operated in synchronous transmission mode, i.e., all nodes transmit simultaneously. We also assume that the maximum delay spread of the channel is τ = 3 μs [ 11 ]. Thus, the number of resolvable paths is considered as Lp = Tτc + 1 = 4, where τ = 3 μs, and the channel’s delay spread profile is negatively exponentially distributed with the factor η in the range of [0.3, 3] μs. The RAKE receiver combines Lr = 3 number of fingers for BER performance evaluation, and the channel’s exponential decay factor is η = 0.2. In our simulation, the LS(4,32,4) codes are deployed as the spreading codes. More explicitly, the total length of the LS(4,32,4) code is L = NP + 2W0 = 136 chips, and its spreading factor may be calculated by simply noting that each bit to be transmitted is spread by one of the constituent LS(4,32,4) codes. Although the length of this LS code is L = NP + 2W0 = 136, the effective spreading gain of the LS code is identical to Geff = 128 since the inserting zeros must not be taken into account. The LS(4,32,4) codes are constituted by a total of 128 spreading codes. The width of the IFW WI and the number of supported user K satisfies that: WI = 4, K ≤ 16; WI = 2, 16 < K ≤ 32; WI = 1, 32 < K ≤ 64; WI = 0, 64 < K ≤ 128. First, we investigated the BER performance of CDD when there existed a strong interference CDD node. In this scenario, a cell has three CDD nodes, the source node, the destination node, and the interference node. In our simulation, the interference node has a transmission power 20 dB higher than the source node. It is obvious that the distance between the interference node and destination node dramatically affects the performance of the RAKE receiver since the strength of interference is inversely proportional to the distance. Figure 5 exhibits the BER performance of the destination node in conjunction with the distance between the interference node and destination node. More explicitly, we can observe that when the width of IFW WI is below 2 and the distance of the interference node is less than 300 m, the effect of the interference node cannot be completely rejected by the interference spreading code so that the MAI leak inevitably in the RAKE receiver due to the insufficient width of the IFW. However, when the WI increases to 3 G=128, SNR=20dB, K=2, η=0.2,m=1, Lr=3 Lp=4, W =0 I W =1 I W =2 I W =3 I W =4 I 10−1 10−2 10−4 10−1 10−2 Fig. 6 BER vs Eb/N0 performance in the context of the ad hoc and cellular scenarios 0 100 200 300 400 500 600 700 Distance to Interfernce Node[m] 800 900 1000 or 4, the interference is suppressed significantly and the effect of the interference node is negligible. The performance of CDD in two common scenarios is shown in Fig. 6. In the cellular scenario, a center node or Base Station (BS) exists in the network, which has a high transmission power than other nodes. In our simulation, we assume that the base station node has a 20-dB higher transmission power. The second is an ad hoc scenario where each node has the same transmission power. Figure 6 plots the BER performance of the CDD communication system in the context of a various number of users K. In Fig. 6, we can observe that the performance in the ad hoc scenario is superior than that in the cellular scenario. This phenomenon is reasonable since the cellular environment exists as a strong base station which also acts as a strong interference node to other destination nodes and then degrades the BER performance in the cellular condition. Figures 7 and 8 exhibit the performance of the CDD system in conjunction with various supported users K. From Fig. 7, we can observe that the near interferencefree performance can be achieved when the number of users K is less than 16 since the spreading codes have the maximum width of the IFW in this condition. As G=128, η=0.2, m=1, Lr=3 Lp=4, Analytical result Ad−hoc Scenario K=16 Analytical result Ad−hoc Scenario K=32 Analytical result Celluar Scenario K=16 Analytical result Celluar Scenario K=32 Simulation result Ad−hoc Scenario K=16 Simulation result Ad−hoc Scenario K=32 Simulation result Celluar Scenario K=16 Simulation result Celluar Scenario K=32 15 Eb/N0[dB] the number of users is increased to 32, the performance of the CDD system is degraded moderately, since the width of the IFW is still maintained in WI ≤ 2. However, when the number of users is increased to more than 64, the performance is degraded significantly since the width of IFW is decreased to 0 ∼ 1, which reduces the capability of combating the MAI. Figure 8 portrays the BER performance of the CDD in conjunction with various users K. Two different SNR parameters are configured in our simulation, i.e., SNR = 10 dB and SNR = 20 dB, respectively. From Fig. 8, we can conclude that the CDD system exhibits a near interference-free performance in the case K ≤ 32. In Figs. 7 and 8, it is advocated that the CDD system should be deployed in a relatively-low 10−1 10−2 10−4 10−1 10−2 10−4 0 20 40 100 120 60 80 Number of Users K load of users. For a spreading gain of 128 systems, the CDD system can support K = 40 user communications simultaneously without the mutual interference; this load is promising since the linear Minimum Mean Square Estimator (MMSE) multiuser detector with a much higher complexity can only support to K = 40 to achieve an ideal performance. Similarly, the performance of the linear MMSE multiuser detector [ 26, 27 ], the Parallel Interference Canceller (PIC) [ 26, 27 ], and Serial Interference Canceller (SIC) [ 26, 27 ] deteriorates significantly for the high load scenario in a CDMA system; furthermore, the traditional MMSE detector, PIC, and SIC suffer the serious near-far effect and degrade the performance in our CDD scenarios. The ideal Maximum Likelihood detector [ 26, 27 ] can solve this issue; however, the complexity of the ML detector is excessively high so that it is impossible to implement in practical communication systems. Finally, Fig. 9 plots the BER performance of different channel fading models. The Nakagami-m channel is a generic model for the wireless channel, where the choice of the parameter m determines the fading type of the channel model. In Fig. 9, three different fading models are simulated and analyzed in our investigation. More explicitly, the Rayleigh fading [ 1, 18 ], Rician fading [ 1, 18 ], and Gaussian Fading [ 1, 18 ] are evaluated in the simulation. In the practical applications in a cellular communication, the Rayleigh fading and Rician fading model are commonly adopted for the performance evaluation. Hence, in this detection, we evaluate the CDD performance in conjunction with the real scenario of the cellar communications. The simulation results in Fig. 9 conform to the mathematic analysis, and we can conclude that the performance of Rayleigh fading is the worst and the performance of Gaussian fading is the best amongst these three fading models. 6 Conclusions In this paper, we investigated the BER performance of the CDD communication system, which can exhibit the same operation fashion as the NDD device. Moreover, the advantage of the CDD is that the receiver can be simplified as the matched filter or RAKE receiver by carefully selecting our proposed interference rejection codes—LS codes. Hence, our proposed method can significantly reduce the complexity and difficulty in the implementation of the NDD fashion. Our simulation results show that the CDD system can achieve a near interference-free performance in a low-user load scenario due to the limited number of available LS codes having a certain IFW width; more explicitly, our simulation and analysis show that the CDD system can achieve an ideal performance when the number of user K ≤ 32, and in this condition, a simple matched filter or RAKE receiver is sufficient to combat all the interference. For future research, the method of the smart assignment of the spreading codes will be investigated to reduce interference between neighboring nodes and increase the capacity and spectrum efficiency of the CDD network. 10−1 10−2 10−4 G=128, K=16, η=0.2, Lr=3 Lp=4, m=1/2, Rayleigh fading m=2, Rician fading m=10, Gussian fading 0 5 10 20 25 30 Fig. 9 BER performance of the CDD communication system in adjunction with different fading channel models Authors’ contributions YY and HW contributed to the conception and design of the study. YY, LL, GL, and HW contributed to the acquisition of data and simulation. YY, GL, LL, and HW contributed to the analysis and interpretation of the simulation data. All authors read and approved the final manuscript. Authors’ information Dr. Yufang Yin obtained her Ph.D. degree in 2007 from the EE department, the University of Texas at San Antonio. From January 2009 to June. 2012, she worked as the specialist and research scientist in Nokia Networks. From July 2012 to October 2014, she worked as the staff engineer in Spread Spectrum Communication. Since November 2016, she joined Chengdu Technological University. Her research area includes statistical signal processing and applied machine learning. Gangjun Li received the B.S. degree in Mechanical Engineering from the University of Electronic Science and Technology of China in 1987 and the M.S. degree in Mechanics from the Harbin Institute of Technology in 1990. He received the Ph.D. degree in Robotics Engineering from the Southwest Jiaotong University in 2002. Since 2010, he is a professor of Chengdu Technological University (CDTU). His research interests are in areas of robotics, simulation, modeling of complex systems, and nonlinear control. Dr. Li (Alex) Li obtained his Ph.D. degree in electronics engineering from the University of York in 2014, and now he is working in Chengdu University of Information Technology, China. His research interests include fields of wireless communication, MIMO-OFDM, adaptive filtering, and ASIC design. Hua Wei obtained his Ph.D. degree from the ECS department, University of Southampton in September 2005. From January 2006 to September 2014, he worked as the principle engineer in Spread spectrum Communication for wireless modem design. Since September 2014, he joined in Chengdu University of information Technology. His research area includes adaptive equalization, signal processing, and VLSI design for wireless baseband processor. Competing interests The authors declare that they have no competing interests. Publisher’s Note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. 1. A GoldSmith , Wireless communications . (Cambridge University Press, 2005 ) 2. T Riihonen , S Werner , R Wichman, Mitigation of loopback self-interference in full-duplex MIMO relays . IEEE Trans. Sign. Process . 59 ( 12 ), 5983 - 5993 ( 2011 ) 3. M Duarte , C Dick , A Sabharwal , Experiment-driven characterization of fullduplex wireless systems . IEEE Trans. Wirel. Commun . 1 ( 12 ), 4296 - 4307 ( 2012 ) 4. L Hanzo , LL Yang, EL Kuan, K Yen, Single- and multi-carrier DS -CDMA. (John Wiley and IEEE Press, 2003 ), p. 1060 5. P Fan , L Hao, Generalized orthogonal sequences and their applications in synchronous CDMA systems . IEICE Trans. Fundam. E83-A , 2054 - 2069 ( 2000 ) 6. S Sta n´czak, H Boche, M Haardt, in GLOBECOM '01. Are LAS-codes a miracle? vol. 1 ( IEEE Global Telecommunications Conference , San Antonio, 2001 ), pp. 589 - 593 7. CC Tseng , CL Liu, Complementary sets of sequences . IEEE Trans. Inf. Theory . 18 , 644 - 652 ( 1972 ) 8. H Wei , L Hanzo , On the uplink performance of asynchronous LAS-CDMA . IEEE Trans. Wirel. Commun . 5 , 1187 - 1196 ( 2006 ) 9. H Wei , L-L Yang , L Hanzo , Interference-free broadband single- and multi-carrier DS-CDMA . IEEE Commun. Mag . 43 ( 2 ), 68 - 73 ( 2005 ) 10. S Ni , H Wei, JS Blogh , L Hanzo , Network performance of asynchronous UTRA-like FDD/CDMA systems using loosely synchronised spreading codes . IEEE Veh. Technol. Conf. 2 , 1359 - 1363 ( 2003 ) 11. WCY Lee , Mobile communications engineering , 2nd ed. ( McGraw-Hill , New York, 2008 ) 12. L-L Yang , W Hua , L Hanzo, Multiuser detection assisted time- and frequency-domain spread multicarrier code-division multiple-access . IEEE Trans. Veh. Technol . 55 ( 1 ), 397 - 404 ( 2006 ) 13. H Wei , L-L Yang , L Hanzo , Downlink space-time spreading using interference rejection codes . IEEE Trans. Veh. Technol . 55 ( 6 ), 1838 - 1847 ( 2006 ) 14. H Wei , L Hanzo, in 2005 6th IEE International Conference on 3G and Beyond . LAS-CDMA Using Various Time Domain Chip-Waveforms (IET Conference Publications , 2005 ) 15. X Liu , H Wei , L Hanzo , Analytical bit error rate performance of DS-CDMA ad hoc networks using large area synchronous spreading sequences . IET Commun . 1 ( 4 ), 760 - 764 ( 2007 ) 16. RL Frank, Polyphase complementary codes . IEEE Trans. Inf. Theory . 26 , 641 - 647 ( 1980 ) 17. R Sivaswamy , Multiphase complementary codes . IEEE Trans. Inf. Theory . 24 , 546 - 552 ( 1978 ) 18. D Tse , P Viswanath , Fundamentals of wireless communication . (Cambridge University Press, 2005 ) 19. JG Proakis, Digital communications, 3rd edn . ( Mc-Graw Hill International Editions , 1995 ) 20. N Nakagami , in Statistical methods in radio wave propagation, ed. by WG Hoffman . The m-distribution, a general formula for intensity distribution of rapid fading (Pergamon , Oxford, 1960 ) 21. T Eng , LB Milstein, Coherent DS-CDMA performance in Nakagami multipath fading . IEEE Trans. Commun . 43 , 1134 - 1143 ( 1995 ) 22. V Aalo , O Ugweje , R Sudhakar , Performance analysis of a DS/CDMA system with noncoherent M-ary orthogonal modulation in Nakagami fading . IEEE Trans. Veh. Technol . 47 , 20 - 29 ( 1998 ) 23. M-S Alouini , AJ Goldsmith , A unified approach for calculating error rates of linearly modulated signals over generalized fading channels . IEEE Trans. Commun . 47 , 1324 - 1334 ( 1999 ) 24. MK Simon , M-S Alouini , A unified approach to the probability of error for noncoherent and differentially coherent modulation over generalized fading channels . IEEE Trans. Commun . 46 , 1625 - 1638 ( 1998 ) 25. 3GPP2, Overviews of the CDMA2000 standards . Website: www.3gpp2.org 26. X Wang , VH Poor, Wireless communication systems: advanced techniques for signal reception . (Prentice Hall , 2011 ) 27. HV Poor , L Tong , Signal processing for wireless communication system . (Springer , 2012 )


This is a preview of a remote PDF: https://link.springer.com/content/pdf/10.1186%2Fs13638-017-0937-9.pdf

Yufang Yin, Gangjun Li, Li Li, Hua Wei. On the performance of the Code Division Duplex system using interference rejection codes, EURASIP Journal on Wireless Communications and Networking, 2017, 149, DOI: 10.1186/s13638-017-0937-9