Optimization of Acid Protease Production by Aspergillus niger I1 on Shrimp Peptone Using Statistical Experimental Design
Optimization of Acid Protease Production by Aspergillus niger I1 on Shrimp Peptone Using Statistical Experimental Design
Rayda Siala,1 Fakher Frikha,2,3 Samiha Mhamdi,1 Moncef Nasri,1 and Alya Sellami Kamoun1,2
1Laboratoire de Génie Enzymatique et de Microbiologie, Ecole Nationale d’Ingénieurs de Sfax, Université de Sfax, BP 1173-3038, Sfax, Tunisia
2Faculté des Sciences de Sfax, Université de Sfax, BP 1171-3000, Sfax, Tunisia
3Laboratoire de Génie Enzymatique des Lipases, Ecole Nationale d’Ingénieurs de Sfax, Université de Sfax, BP 1173-3038, Sfax, Tunisia
Received 24 October 2011; Accepted 5 January 2012
Academic Editors: W. Hunziker and Y. Ueta
Copyright © 2012 Rayda Siala et al. This is an open access article distributed under the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.
Medium composition and culture conditions for the acid protease production by Aspergillus niger I1 were optimized by response surface methodology (RSM). A significant influence of temperature, KH2PO4, and initial pH on the protease production was evaluated by Plackett-Burman design (PBD). These factors were further optimized using Box-Behnken design and RSM. Under the proposed optimized conditions, the experimental protease production (183.13 U mL−1) closely matched the yield predicted by the statistical model (172.57 U mL−1) with ?2=0.914. Compared with the initial M1 medium on which protease production was 43.13 U mL−1, a successful and significant improvement by 4.25 folds was achieved in the optimized medium containing (g/L): hulled grain of wheat (HGW) 5.0; KH2PO4 1.0; NaCl 0.3; MgSO4(7H2O) 0.5; CaCl2 (7H2O) 0.4; ZnSO4 0.1; Na2HPO4 1.6; shrimp peptone (SP) 1.0. The pH was adjusted at 5 and the temperature at 30∘C. More interestingly, the optimization was accomplished using two cheap and local fermentation substrates, HGW and SP, which may result in a significant reduction in the cost of medium constituents.
Microorganisms are the most important sources for enzymes production. Among these enzymes, proteases account for nearly 60% of the total industrial enzyme market [1, 2]. A large proportion of commercially available proteases are currently derived from Bacillus strains. Nevertheless, the potential use of fungal proteases is being increasingly realized . In fact, fungal enzymes are commonly used in industries due to various technical reasons, including the feasibility of obtaining enzymes at high concentration in the fermentation medium . Fungal proteases offer a distinct advantage over bacterial enzymes in terms of ease of downstream processing .
The use of acid proteases has been increased remarkably in various industrial processes such as animal feed, cheese and food processing, and X-ray films [6, 7].
It is well known that extracellular protease production by microorganisms is greatly influenced by media components, especially carbon and nitrogen sources, and physical factors such as temperature, pH, incubation time, agitation, and inoculum density [8–11]. Medium composition is one of the most important parameters when enzymes are produced for industrial purposes particularly, because around 30–40% of the production cost was estimated to be accounted for the cost of the growth medium . Then, the use of local and low cost substrates in growth media can significantly reduce the cost of enzyme production . Fish by-products have been used to a minor extent as a fermentation substrate for protease production, despite their availability in large quantities and their low cost. Ellouz et al.  have shown that protease synthesis was strongly induced when B. subtilis was grown in media containing only sardinelle heads and viscera powder. Haddar et al.  had reported the use of hulled grain of wheat and Sardinella aurita peptone for the proteases production by B. mojavensis A21. Also, Hadj-Ali et al.  demonstrated efficient utilization of both fish powders and hulled grain of wheat as bacterial growth substrates for alkaline proteases production by B. licheniformis NH1.
The protease production by B. cereus BG1 was stimulated by the use of S. aurita powders .
Optimization of media compounds by the traditional “one-variable-at-a-time” strategy involving changing one independent variable is the most frequently used operation in biotechnology . This strategy is extremely time-consuming and expensive when a large number of variables are considered and incapable of detecting the true optimum, due especially to the interactions among the factors.
In recent years, the use of statistical approach involving Plackett-Burman designing and Box-Behnken design has gained lot of impetus for medium optimization and for understanding the interactions among various physicochemical parameters using a minimum number of experiments. The Plackett-Burman design allows the screening of main factors, from a large number of variables that can be retained in further optimization process. Box-Behnken design is a collection of statistical techniques for designing experiments, building models, evaluating the effects of factors, and searching optimum conditions of studied factors for desirable responses . Box-Behnken design has been successfully applied in many areas of biotechnology, such as manganese peroxidase production , protease production [15, 21], and neomycin production .
Aspergillus niger I1 has been recently isolated and identified as a producer of an extracellular bleaching stable acid protease . The enzyme has a molecular weight of 49 kDa, it was identified as an aspartic protease, with optimum at pH 3 and 60°C. These properties would make this enzyme potentially useful for industrial applications. In the present study, an effort was done to maximize the acid protease production by A. niger I1 by using low-cost fermentation medium. The optimization steps were performed as follows: selecting carbon and nitrogen sources by one-variable-at-a-time approach, screening the main factors influencing protease production using Plackett-Burman design, and assessing the optimal region of the significant variables using Box-Behnken design.
2. Material and Methods2.1. Material
All chemicals used were of analytical grade. Hulled grain of wheat (HGW) was purchased from a local industry. Shrimp flower (SF), shrimp peptone (SP), combined heads and viscera sardinelle (Sardinella aurita) powder (CHVSP), and Mirabilis jalapa tubers powder (MJTP) were prepared in our laboratory.
To obtain CHVSP, sardinelle heads and viscera were cooked until boiling, pressed to remove water and fat, minced, and then dried according to Ellouz et al. . MJTP was prepared as described by Hajji et al. .
SF was prepared as follows: shrimp wastes, collected from a local fish processing industry, were washed thoroughly with tap water and then cooked for 20 min at 100°C. The solid material obtained was dried, minced to obtain a fine powder, and then stored in a glass bottle at room temperature. The chemical composition (proteins, chitin, lipids, and ash) was determined by Manni et al. . SP was obtained by hydrolysing SF by commercial trypsin.
A. niger I1 producing an acid protease was used in the present study. It was identified on the basis of a 650 bp PCR amplified DNA fragment of the 18S rDNA sequence .
The strain was propagated on potato-dextrose-agar plates at 30°C, and inocula were prepared from 7-days-old mycelia by flooding with 10 mL of sterile distilled water and scraping off the agar plates.
2.3. Carbon and Nitrogen Sources Selection
Initial screening of the most significant carbon and nitrogen sources allowing the maximum protease production was performed by one-variable-at-a-time approach. Seven different nitrogen sources (5 g/L), including casein peptone, meat peptone, urea, gelatine, sodium chloride, yeast extract, SP or ammonium sulphate and eight simple or complex carbon sources (10 g/L) including glucose, maltose, lactose, HGW, MJTP, SF, CHVSP, and casein, were tested. Initial M1 medium consists of (g/L): HGW 10.0; (NH4)2SO4 5.0; CaCl2(7H2O) 0.4; KH2PO4 1.0; Na2HPO4 0.8; MgSO4(7H2O) 0.5; ZnSO4 0.1; NaCl 0.3. Media were autoclaved at 120°C for 20 min. Cultures were inoculated with 107 spores/mL in 300 mL Erlenmeyer flasks with a working volume of 50 mL and incubated in a rotatory shaker (200 rpm) for 72 h. Cultures were centrifuged at 8,000 ×g for 15 min to remove fungi mycelia, and the supernatant was used for estimation of proteolytic activities. It will be designated in the text by enzyme preparation.
All experiments were carried out in duplicate and repeated at least twice.
2.4. Estimation of the Fungal Growth
Growth was estimated by the determination of the mycelium dry weight. The fungal mycelia were harvested by centrifugation at 8,000 ×g for 15 min. The pellet was washed with autoclaved bidistilled water, and the dry weight was determined after heating at 105°C until a constant weight .
2.5. Protease Assay
Protease activity was measured by the method of Kembhavi et al.  using hemoglobin as a substrate. Enzyme preparation (0.5 mL), suitably diluted, was mixed with 0.5 mL of hemoglobin 1% (w/v) in 100 mM glycine-HCl (pH 3.0) and then incubated for 5 min at 60°C. The reaction was stopped by adding 0.5 mL trichloroacetic acid 8% (w/v). The mixture was allowed to stand at room temperature for 15 min and then centrifuged at 10,000 ×g for 15 min to remove the precipitate. The absorbance of the soluble fraction was estimated at 280 nm. A standard curve was generated using tyrosine solutions at 0–50 mg/L. One unit of protease activity was defined as the amount of enzyme required to liberate 1 μg of tyrosine per min under the experimental conditions.
2.6. Plackett-Burman Design
The Plackett-Burman design is an efficient way to screen the main physicochemical parameters, required for elevated production, among a large number of process variables . The carbon and nitrogen sources, which had been screened earlier, were added to the main culture medium for optimization. The Plackett-Burman method allows evaluation of N variables in ?+1 experiments; each variable was examined at two levels: (−1) for a low level and (+1) for a high level. Table 1 illustrates the factors under investigation as well as levels of each factor used in the experimental design. Whereas Table 2 represents the design matrix “Design Expert 7.0” Stat-Ease, Inc., Minneapolis, USA, and was used to analyze the experimental Plackett-Burman design.
Table 1: Levels of the factors tested for the production of proteases by A. niger I1 using Plackett-Burman design.
Table 2: Plackett-Burman experimental design matrix with proteolytic enzymes production levels.
2.7. Experimental Design
A Box-Behnken design of RSM was employed to optimize the three most significant factors (KH2PO4, pH, and temperature) for enhancing protease production, screened by Plackett-Burman design, the three independent factors were investigated at three different levels (−1, 0, +1), and the experimental design used for study is shown in Table 3. The protease production was fitted using a second-order polynomial equation, and multiple regression of the data was carried out for obtaining an empirical model related to the most significant factors. The general form of the second-order polynomial equation is?=?0+????+????2?+???????,(1)
Table 3: The Box-Behnken design of RSM for optimization of protease production.
where Y is the predicted response, ?? and ?? are independent factors, ?0 is the intercept, ?? is the linear coefficient, ??? is the quadratic coefficient, and ??? is the interaction coefficient.
Design-Expert, version 7.0 (STAT-EASEinc, Minneapolis, USA), was used for experimental designs and statistical analysis of the experimental data. The analysis of variance (ANOVA) was used to estimate the statistical parameters.
2.8. Biochemical Properties of the Crude Enzyme Preparation2.8.1. Effect of pH and Temperature on Enzyme Activity and Stability
The optimum pH of the enzyme preparation was studied over a pH range of 3.0–9.0 at 50°C using hemoglobin 1% (w/v). For studying pH stability, the crude enzyme was incubated in buffers of different pH values in the range of pH 3.0–9.0 for 1 h at 30°C. Residual proteolytic activity was then determined under standard assay conditions. The following buffer systems were used: 100 mM glycine-HCl buffer for pH 3.0, 100 mM sodium acetate buffer for pH 4.0–6.0, 100 mM potassium phosphate buffer for pH 7.0, 100 mM Tris-HCl buffer for pH 8.0, and 100 mM glycine-NaOH buffer for pH 9.0.
To investigate the effect of temperature, proteolytic activity was tested at different temperatures using hemoglobin as a substrate for 5 min at pH 4.0. Thermal stability was examined by incubating the enzyme for 60 min at 30, 40, 50, and 60°C. Aliquots were withdrawn at desired time intervals to test the remaining activity at optimum conditions of pH and temperature. The nonheated enzyme was considered as the 100% control.
2.8.2. Effects of Metal Ions and Inhibitors on Proteolytic Activity
The effect of various metal ions at 5 mM on enzyme activity was investigated using CaCl2, MnSO4, ZnSO4, CoSO4, CuSO4, BaCl2, FeCl2, HgCl2, MgSO4, NaCl, and KCl.
The effects of inhibitors on protease activity were studied using phenylmethylsulfonyl fluoride (PMSF), pepstatin A, β-mercaptoethanol, and ethylenediaminetetraacetic acid (EDTA). The enzyme preparation was preincubated with inhibitor for 60 min at 4°C, and then the remaining proteolytic activity was estimated using hemoglobin as a substrate. The activity of the enzyme without any additive was taken as the 100% control.
For zymography, casein was used as substrate. Casein-zymography was performed to estimate the number of the proteolytic activity in the crude supernatant. Zymography was performed in conjunction with SDS-PAGE according to the method of Garcia-Carreno et al.  with a slight modification. SDS-PAGE was performed as described by Laemmli , using a 5% (w/v) stacking gel and a 12% (w/v) separating gel. The samples were not heated. After electrophoresis, the gel was submerged in 100 mM glycine-HCl pH 3.0 (buffer A) containing 2.5% Triton X-100 for 60 min, with constant agitation to remove SDS. Triton X-100 was then removed by washing the gel three times with buffer A. The gel was then incubated with 1% (w/v) casein in buffer A for 15 min at 50°C. Finally, the gel was stained with Coomassie brilliant blue R-250 for zymography analysis. The development of clear zone on the blue background of the gel indicated the presence of protease activity. The molecular mass markers used in SDS-PAGE were phosphorylase b (97 kDa); albumin (66 kDa); ovalbumin (45 kDa); carbonic anhydrase (30 kDa); trypsin inhibitor (20.1 kDa); bovine α-lactoalbumin (14.4 kDa).
3. Results3.1. Selection of Carbon and Nitrogen Sources
A series of experiments was first carried out to study the effects of various simple and complex carbon and nitrogen sources on protease production by A. niger. Cultures were first conducted in medium M1 containing different carbon sources, each added at a concentration of 10 g/L. Protease activity was produced at high levels in the presence of complex organic carbon sources (Figure 1(a)). The highest level was obtained with HGW (43.13 U mL−1) followed by CHVSP and MJTP (37.34 and 34.24 U mL−1, resp.). HGW and MJTP were tested as carbon sources since they contained high starch content 62 and 32.6 ± 2%, respectively. The easily assimilated simple carbon sources like maltose, glucose, and lactose resulted in weak acid protease production, 14.37, 3.33, and 1.24 U mL−1, respectively.
Figure 1: Effects of carbon sources at 10 g/L (a); nitrogen sources at 5 g/L (b) on the production of proteolytic activity by A. niger I1. HGW: hulled grain of wheat, MJTP: Mirabilis jalapa tuber powder, SF: shrimp flower, CHVSP: combined heads and viscera sardinelle powder, MP: meat peptone, SP: shrimp peptone, AC: ammonium chloride, YE: yeast extract, AS: ammonium sulphate, CP: casein peptone.
In general, both organic and inorganic nitrogen sources were used efficiently for protease production. In the present study, six organic (yeast extract, casein peptone, gelatine, CHVSP, meat peptone, and SP) and two inorganic nitrogen sources (ammonium sulphate and ammonium chloride) were tested, at a concentration of 5 g/L, in M1 medium containing HGW at 10 g/L as carbon source (Figure 1(b)). Among the various nitrogen sources studied, A. niger I1 produced high levels of protease on SP (82.3 U mL−1) followed by meat peptone, casein peptone, CHVSP, yeast extract, and gelatine (72.67, 71.63, 68.75, 61.24, and 55.68 U mL−1, resp.). Ammonium sulphate and ammonium chloride showed weak acid protease production levels, 39.8 and 25.49 U mL−1, respectively.
Among the various carbon and nitrogen sources tested, HGW and SP were found to be the most suitable substrates for the production of acid protease by A. niger I1. Thus, these substrates were selected for further optimization steps.
3.2. Selection of Significant Variables by Plackett-Burman Design
Analysed by design Expert, a first-order model was fitted to results obtained from the twelve experiments.
The t-test was used to identify the effect of each factor on protease production. Table 4 shows that KH2PO4, initial pH, and temperature are the most significant factors (?<0.05); they were selected for further optimization.
Table 4: Identification of significant variables for proteolytic enzymes production by A. niger I1 using Plackett-Burman design.
According to Table 4, temperature, KH2PO4, and initial pH were determined to be significant factors (?<0.05) on the protease production. Among nonsignificant factors, six factors (HGW, NaCl, MgSO4, CaCl2, ZnSO4, and inoculum’s size IS) exerted a negative effect while two variables (Na2HPO4 and SP) exerted positive effects on proteases production. The significant variables (temperature, initial pH, and KH2PO4) were selected for further optimization by a response surface methodology. The nonsignificant variables with positive effect (Na2HPO4 and SP) were fixed at high levels, while variables with a negative effect (HGW, NaCl, MgSO4, CaCl2, ZnSO4, and IS) were fixed at low levels.
3.3. Optimization of Significant Variables Using RSM
Box-Behnken design was used to determine the optimum values of the three selected significant variables (temperature, initial pH, and KH2PO4 concentration) for the protease production. A total of 17 experiments with different combinations of the three selected variables were performed. The design matrix with the corresponding results of Box-Behnken experiments, as well as the predicted results, is presented in Table 4. The ? values for the model (<0.0001) and for “Lack of Fit” (0.0687) also suggested that the obtained experimental data was a good fit with the model. The regression equation coefficients were calculated, and the data were fitted to a first-order polynomial equation. The response of protease production (?) by A. niger I1 can be expressed in terms of the following regression equation:?=+55.20−3.83?1+12.20?3−8.16?1?3,(2)
where ?1 is KH2PO4 concentration; ?3 is temperature.
The ANOVA analysis of the optimization study (Table 5) indicated that, among the three significant variables selected by the Plackett-Burman design experiment, KH2PO4 and temperature were found to have a significant effect on enzyme production contrary to pH. Furthermore, the interaction between KH2PO4 and temperature (X1X3) was significant, as was shown by the low ? value (0.0001) for the interactive terms.
Table 5: Analysis of variance for response surface 2FI model (partial sum of squares, type III).
The regression equation obtained from the ANOVA analysis showed that the value of ?2 (multiple correlation coefficient) is 0.914. This value indicated that only 10.884% of the total variation was not explained by the model. The value of the adjusted determination coefficient (Adj-?2=0.894) further confirms the significance of the model. The value of the predicted determination coefficient pred-R2 of 0.7841 is in reasonable agreement with the value of the adjusted determination coefficient Adj-R2 of 0.8939. In addition, the model has an adequate precision value of 24.832. This suggests that the model can be used to navigate the design space (Table 6).
Table 6: Variance analysis (ANOVA) of the model 2FI (partial sum of squares, type III).
The lower reliability of the experiment is usually indicated by the high value of the coefficient of variation (CV) . In the present case, a low CV (6.126%) denotes that the experiments performed are highly reliable as was shown by Mohanasundararaju et al. .
Response surface plot was generally the graphical representation of the regression equation, from which the response (protease production) is plotted against any two variables (Figures 2(a), 2(b), and 2(c)), while other variables were fixed at their middle levels.
Figure 2: Response surface plot of proteolytic enzyme production showing the interactive effects of the temperature and KH2PO4 concentrations (a, b), and initial pH, temperature, and KH2PO4 concentrations (c).
As shown in Figures 2(b) and 2(c), protease production increased only when temperature increased and could not increase with KH2PO4 concentration. The model predicted that the maximum proteolytic enzyme production of 172.57 U mL−1 is achieved in the medium containing (g/L): HGW 5; SP 5; KH2PO4 1; Na2HPO4 1.6; CaCl2(7H2O) 0.4; ZnSO4 0.1; NaCl 0.3; MgSO4(7H2O) 0.5; pH 5.0.
3.4. Model Validation
The experimentally determined production values were found to be in good agreement with the statistically predicted ones (?2=0.914), confirming the model’s authenticity. In addition, the “Pre-?2” of 0.7841 is in reasonable agreement with the “Adj-?2” of 0.8939, indicating that this model can be used to navigate the design space (Table 6).
3.5. Casein Zymography
Casein zymography of the crude enzyme preparation revealed the presence of one clear zone, suggesting the presence of one acid protease (Figure 3). The molecular mass of the A. niger I1 protease was estimated to be 49.4 kDa by SDS-PAGE.
Figure 3: SDS-PAGE and zymography of A. niger I1 crude enzyme preparation. Lane 1: zymography on casein; lane 2: SDS-PAGE after staining with Coomassie blue R250; lane 3: molecular mass markers.
3.6. Biochemical Properties of Proteolytic Enzyme3.6.1. Effect of pH on Enzyme Activity and Stability
The effect of pH on the activity of the crude enzyme was determined over a pH range of 3.0–9.0 at 60°C using hemoglobin as substrate. As shown in Figure 4(a), the A. niger I1 enzyme preparation exhibited maximum activity at pH 4.0.
Figure 4: Effect of pH on the activity (a) and stability (b) of the extracellular proteases of A. niger I1 strain. pH optima were determined by incubating the crude enzyme with the substrate at different pH values at 60°C. The maximum activity obtained at pH 3.0 with hemoglobin as substrates was considered to be 100%. The pH stability was determined by incubating the crude enzyme in different buffers for 1 h at 4°C, and the residual activity was measured at pH 3.0 and 60°C with hemoglobin as a substrate. The activity of the enzyme before incubation was taken as 100%.
The pH stability of the crude enzyme was studied by assaying the residual activity of the proteolytic enzyme after incubation at 4°C for 1 h in buffers of various pH values. The crude enzyme was highly stable over a wide pH range, maintaining more than 86 and 80% of its initial activity at pH 3.0 and 5.0, respectively (Figure 4(b)). However, proteolytic enzyme activity decreased significantly below pH 6. The enzyme was inactivated at pH 7, 8, and 9.
3.6.2. Effect of Temperature on Enzyme Activity and Stability
The influence of temperature on the crude supernatant was examined at pH 4.0 using hemoglobin as substrate. The temperature activity profile showed that the crude enzyme was highly active between 30°C and 60°C with an optimal activity at 50°C using hemoglobin as substrate (Figure 5(a)).
Figure 5: Effect of temperature on the activity (a) and stability (b) of the extracellular proteinases of A. niger I1. The temperature profile was determined by assaying proteolytic activity at temperatures between 30°C and 70°C. The activity of the enzyme at 50°C and pH 4.0 using hemoglobin as a substrate was taken as 100%. The temperature stability was determined by incubating the crude enzyme in different temperature for 1 h, and the residual activity was measured at pH 4.0 and 50°C with hemoglobin as a substrate. The nonheated enzyme was considered as 100% control.
To examine the thermal stability of A. niger I1 protease, the enzyme preparation was incubated at pH 4, at various temperatures for different time periods, and then the residual activities were measured. The thermal stability profile of the crude enzyme showed that the enzyme is highly stable at temperatures below 30°C (Figure 5(b)). At 30°C, the enzyme remains fully active even after 1 h incubation. The enzyme was rapidly inactivated at 70°C, losing 93% of its initial activity after 15 min incubation.
3.6.3. Effects of Metal Ions and Enzyme Inhibitors on Enzyme Activity
The effects of various metal ions (5 mM) on the proteolytic activity of the enzyme preparation were studied at pH 4.0 and at 50°C by the addition of the respective cations or enzyme inhibitor to the reaction mixture. As shown in Table 7, the addition of K+ increased slightly proteolytic activity. However, Hg2+ and Cu2+ inhibited the proteolytic activity by 22% and 39.12%, respectively. Ca2+ and Zn2+ had no influence on enzyme activity. The crude enzyme was completely inhibited by pepstatin A. PMSF and EDTA are practically without influence on the activity of the crude enzyme.
Table 7: Effect of some metal ions and inhibitors on A. niger I1 protease activity.
4. Discussion and Conclusion
In general, no defined medium has been carried out for the optimum production of proteases from different microbial strains . Each microorganism has its own special conditions for the maximum enzyme production. Several researchers attempted to induce protease production by using glucose or starch, coupled with expensive nitrogen sources such as yeast extract, peptone, or casamino acids. However, few studies have been made to induce protease production using inexpensive carbon and nitrogen sources [34–36]. Since shrimp wastes are free, abundant, and polluting the environment, their utilization as substrate by A. niger could result in a twofold benefit, namely, a substantial reduction in the cost of enzyme production and a hygienic treatment of the environment. Indeed, in the present work, shrimp peptone was found to be an excellent substrate for protease induction by A. niger I1. This may be due to the fact that shrimp wastes contain carbohydrates and minerals and a great amount (~40%) of proteins  and then the resulting peptone provides many useful peptides or other molecules, for protease induction or synthesis.
In general, both organic and inorganic nitrogen sources were used efficiently for protease production. The optimum proteolytic activity produced by A. niger I1 was achieved with shrimp peptone as nitrogen source (82.3 U mL−1), followed by casein peptone (71.63 U mL−1) compared to the control with ammonium sulphate as nitrogen source (39.80 U mL−1). The addition of ammonium chloride or urea to the medium containing HGW as carbon source decreased protease synthesis to 25.49 and 3.66 U mL−1, respectively. Through these results, it can be concluded that shrimp peptone is an excellent source of nitrogen for production of extracellular proteases by A. niger I1.
Hajji et al.  studies have established that extracellular protease secretion by A. clavatus ES1 is substantially influenced not only by carbon and nitrogen sources, but also by initial pH and temperature of the growth.
Indeed, in line with these studies, our study showed that KH2PO4 concentration, temperature, and initial pH were found to influence enzymes synthesis. The optimization of these three parameters (KH2PO4 1.0 g/L, pH 5, and 30°C) resulted in a proteolytic activity of 183.13 U mL−1, with a 2.2 increase comparing to 82.3 U mL−1 obtained on the unoptimized medium containing 10.0 g/L HGW and 5 g/L SP.
Our findings are in accordance with those of Luciana and Suto  who demonstrated that KH2PO4 concentration was the most influential variable on proteolytic enzyme production by Cellulosimicrobium cellulans.
Finally, the maximum proteolytic enzyme production was achieved at the following conditions: temperature 30°C, agitation speed of 150 rpm, pH 5.0, and (g/L) HGW, 5, SP, 5; KH2PO4, 1, Na2HPO4, 1.6, CaCl2, 0.4, ZnCl2, 0.1, NaCl, 0.3, MgSO4(7 H2O), 0.5; other salts were taken at their low levels as shown in Plackett-Burman design. By optimizing the medium composition and the culture conditions, not only the production of proteases was enhanced by 4.25-fold from 43.13 to 183.13 U mL−1 but also the cost of enzyme production was reduced since two cheap and readily available complex fermentation substrates HGW and SP were used.
The use of statistical models to optimize culture medium components and conditions has increased in present-day biotechnology, due to its easy applicability, reliability, and validity. In the present study, the significant variables necessary for the enhancement of proteolytic enzyme production were selected using the Plackett-Burman design. The RSM applied to the optimization of proteases production in this investigation suggested the importance of a variety of factors at different levels. RSM was successfully applied in the production of proteases by A. awamori  and A. terreus .
In this study, A. niger I1 was found to produce at least only one acid protease as revealed by casein zymography. Van den Hombergh et al.  reported at least three aspartic proteases for a strain of A. niger. Nevertheless, other works reported the production of only one proteolytic enzyme by Aspergillus oryzae MTCC 5341 strain .
The enzyme has its optimum activity at pH 4.0, and then protease activity decreased significantly below and above pH 4.0. Optimum pH values between 3.0 and 5.5 have been reported for other fungi proteases, such as the one of Penicillium camemberti (pH 3.5)  and Rhizopus oryzae (pH 5.5) . The A. niger NRRL 1785 protease exhibited an optimum at pH 4.0 .
The crude enzyme showed maximum activity at 50°C on hemoglobin. The optimum temperature of A. niger I1 was similar to those from other fungi proteases, such as the one of Neosartorya fischeri var. spinosa IBT 4872 . Proteases from R. oryzae , P. duponti K1014 , P. oxalicum , and Cryptococcus albidus  exhibited optimum activity at 60°C.
The effects of various metal ions at a concentration of 5 mM on the activity of A. niger I1 protease were studied at pH 4.0 and 50°C. A. niger I1 acid protease was practically insensitive to the most metallic ions. So this property is in the view of potential food industry applications. None of the metallic ions enhanced protease activity. In this respect, the A. niger I1 enzyme resembles to the acid proteases of Hebeloma crustuliniforme  and Mucor pusillus . The effect of a variety of enzyme inhibitors, such as chelating agent and specific group reagents on the activity, was also investigated. Among the cited proteases produced by A. niger strains [40, 51, 52], the enzyme can be classified as an acid (aspartic) protease and belonged to the A1 family because of its optimal pH at 4.0 and full inhibition by pepstatin A .
In conclusion, this work attempted to demonstrate the efficient use of Plackett-Burman and RSM approaches to determine the conditions leading to enhance extracellular protease production by A. niger I1 on two local and low-cost substrates, HGW and SP.
This work was funded by Ministry of Higher Education and Scientific Research Tunisia.
References M. B. Rao, A. M. Tanksale, M. S. Ghatge, and V. V. Deshpande, “Molecular and biotechnological aspects of microbial proteases,” Microbiology and Molecular Biology Reviews, vol. 62, no. 3, pp. 597–635, 1998. View at Google Scholar · View at ScopusU. C. Banerjee, R. K. Sani, W. Azmi, and R. Soni, “Thermostable alkaline protease from Bacillus brevis and its characterization as a laundry detergent additive,” Process Biochemistry, vol. 35, no. 1-2, pp. 213–219, 1999. View at Publisher · View at Google Scholar · View at ScopusR. Gupta, Q. K. Beg, S. Khan, and B. Chauhan, “An overview on fermentation, downstream processing and properties of microbial alkaline proteases,” Applied Microbiology and Biotechnology, vol. 60, no. 4, pp. 381–395, 2003. View at Publisher · View at Google Scholar · View at ScopusD. A. Mitchell and B. K. Lonsane, “Definition, characteristics and potential in solid state cultivation,” in Applied Biotechnology Series, H. W. Doelle, S. A. Mitchell, and C. E. Rolz, Eds., pp. 1–16, Elsevier, Amsterdam, The Netherlands, 1992. View at Google ScholarR. S. Laxman, A. P. Sonawane, S. V. More et al., “Optimization and scale up of production of alkaline protease from Conidiobolus coronatus,” Process Biochemistry, vol. 40, no. 9, pp. 3152–3158, 2005. View at Publisher · View at Google Scholar · View at ScopusR. Gupta, Q. Beg, and P. Lorenz, “Bacterial alkaline proteases: molecular approaches and industrial applications,” Applied Microbiology and Biotechnology, vol. 59, no. 1, pp. 15–32, 2002. View at Publisher · View at Google Scholar · View at ScopusC. G. Kumar and H. Takagi, “Microbial alkaline proteases: from a bioindustrial viewpoint,” Biotechnology Advances, vol. 17, no. 7, pp. 561–594, 1999. View at Publisher · View at Google Scholar · View at ScopusP. N. Nehete, V. D. Shah, and R. M. Kothari, “Profiles of alkaline protease production as a function of composition of the slant, age, transfer and isolate number and physiological state of culture,” Biotechnology Letters, vol. 7, no. 6, pp. 413–418, 1985. View at Google Scholar · View at ScopusM. M. Kole, I. Draper, and D. F. Gerson, “Production of protease by Bacillus subtilis using simultaneous control of glucose and ammonium concentrations,” Journal of Chemical Technology and Biotechnology, vol. 41, no. 3, pp. 197–206, 1988. View at Google Scholar · View at ScopusH. Varela, M. D. Ferrari, L. Belobrajdic, R. Weyrauch, and L. Loperena, “Short communication: effect of medium composition on the production by a new Bacillus subtilis isolate of protease with promising unhairing activity,” World Journal of Microbiology and Biotechnology, vol. 12, no. 6, pp. 643–645, 1996. View at Google Scholar · View at ScopusB. Johnvesly and G. R. Naik, “Studies on production of thermostable alkaline protease from thermophilic and alkaliphilic Bacillus sp. JB-99 in a chemically defined medium,” Process Biochemistry, vol. 37, no. 2, pp. 139–144, 2001. View at Publisher · View at Google Scholar · View at ScopusO. Kirk, T. V. Borchert, and C. C. Fuglsang, “Industrial enzyme applications,” Current Opinion in Biotechnology, vol. 13, no. 4, pp. 345–351, 2002. View at Publisher · View at Google Scholar · View at ScopusA. Gessesse and B. A. Gashe, “Production of alkaline protease by an alkaliphilic bacteria isolated from an alkaline soda lake,” Biotechnology Letters, vol. 19, no. 5, pp. 479–481, 1997. View at Publisher · View at Google Scholar · View at ScopusY. Ellouz, A. Bayoudh, S. Kammoun, N. Gharsallah, and M. Nasri, “Production of protease by Bacillus subtilis grown on sardinelle heads and viscera flour,” Bioresource Technology, vol. 80, no. 1, pp. 49–51, 2001. View at Publisher · View at Google Scholar · View at ScopusA. Haddar, N. Fakhfakh-Zouari, N. Hmidet, F. Frikha, M. Nasri, and A. S. Kamoun, “Low-cost fermentation medium for alkaline protease production by Bacillus mojavensis A21 using hulled grain of wheat and sardinella peptone,” Journal of Bioscience and Bioengineering, vol. 110, no. 3, pp. 288–294, 2010. View at Publisher · View at Google Scholar · View at ScopusN. E. Hadj-Ali, N. Hmidet, N. Souissi, A. Sellami-Kamoun, and M. Nasri, “The use of an economical medium for the production of alkaline serine proteases by Bacillus licheniformis NH1,” African Journal of Biotechnology, vol. 9, no. 18, pp. 2668–2674, 2010. View at Google Scholar · View at ScopusA. Sellami-Kamoun, B. Ghorbel-Frikha, A. Haddar, and M. Nasri, “Enhanced Bacillus cereus BG1 protease production by the use of sardinelle (Sardinella aurita) powder,” Annals of Microbiology, pp. 1–8, 2010. View at Publisher · View at Google Scholar · View at ScopusP. D. Haaland, “Statistical problem solving,” in Experimental Design in Biotechnology, P. D. Haaland, Ed., pp. 1–18, Marcel Dekker, New York, NY, USA, 1989. View at Google ScholarJ. De Coninck, S. Bouquelet, V. Dumortier, F. Duyme, and I. Verdier-Denantes, “Industrial media and fermentation processes for improved growth and protease production by Tetrahymena thermophila,” Journal of Industrial Microbiology and Biotechnology, vol. 24, no. 4, pp. 285–290, 2000. View at Google Scholar · View at ScopusG. Annadurai, S. Rajesh Babu, G. Nagarajan, and K. Ragu, “Use of Box-Behnken design of experiments in the production of manganese peroxidase by Phanerochaete chrysosporium (MTCC 767) and decolorization of crystal violet,” Bioprocess Engineering, vol. 23, no. 6, pp. 715–719, 2000. View at Publisher · View at Google Scholar · View at ScopusJ. R. Dutta, P. K. Dutta, and R. Banerjee, “Optimization of culture parameters for extracellular protease production from a newly isolated Pseudomonas sp. using response surface and artificial neural network models,” Process Biochemistry, vol. 39, no. 12, pp. 2193–2198, 2004. View at Publisher · View at Google Scholar · View at ScopusK. Adinarayana, P. Ellaiah, B. Srinivasulu, R. Bhavani Devi, and G. Adinarayana, “Response surface methodological approach to optimize the nutritional parameters for neomycin production by Streptomyces marinensis under solid-state fermentation,” Process Biochemistry, vol. 38, no. 11, pp. 1565–1572, 2003. View at Publisher · View at Google Scholar · View at ScopusR. Siala, A. Sellami-Kamoun, M. Hajji, I. Abid, N. Gharsallah, and M. Nasri, “Extracellular acid protease from Aspergillus niger I1: purification and characterization,” African Journal of Biotechnology, vol. 8, no. 18, pp. 4582–4589, 2009. View at Google Scholar · View at ScopusM. Hajji, A. Rebai, N. Gharsallah, and M. Nasri, “Optimization of alkaline protease production by Aspergillus clavatus ES1 in Mirabilis jalapa tuber powder using statistical experimental design,” Applied Microbiology and Biotechnology, vol. 79, no. 6, pp. 915–923, 2008. View at Publisher · View at Google Scholar · View at ScopusL. Manni, K. Jellouli, O. Ghorbel-Bellaaj et al., “An oxidant- and solvent-stable protease produced by bacillus cereus SV1: application in the deproteinization of shrimp wastes and as a laundry detergent additive,” Applied Biochemistry and Biotechnology, vol. 160, no. 8, pp. 2308–2321, 2010. View at Publisher · View at Google Scholar · View at ScopusZ. Chi and S. Zhao, “Optimization of medium and cultivation conditions for pullulan production by a new pullulan-producing yeast strain,” Enzyme and Microbial Technology, vol. 33, no. 2-3, pp. 206–211, 2003. View at Publisher · View at Google Scholar · View at ScopusA. A. Kembhavi, A. Kulkarni, and A. Pant, “Salt-tolerant and thermostable alkaline protease from Bacillus subtilis NCIM No. 64,” Applied Biochemistry and Biotechnology, vol. 38, no. 1-2, pp. 83–92, 1993. View at Publisher · View at Google Scholar · View at ScopusR. L. Plackett and J. P. Burman, “The design of optimum multifactorial experiments,” Biometrika, vol. 33, pp. 305–325, 1946. View at Google ScholarF. L. Garcia-Carreno, L. E. Dimes, and N. F. Haard, “Substrate-gel electrophoresis for composition and molecular weight of proteinases or proteinaceous proteinase inhibitors,” Analytical Biochemistry, vol. 214, no. 1, pp. 65–69, 1993. View at Publisher · View at Google Scholar · View at ScopusU. K. Laemmli, “Cleavage of structural proteins during the assembly of the head of bacteriophage T4,” Nature, vol. 227, no. 5259, pp. 680–685, 1970. View at Publisher · View at Google Scholar · View at ScopusT. Alizadeh and M. Zare, “Enhancement of sensitivity of molecularly imprinted polymer based parathion voltammetric sensor by using experimental design techniques,” Analytical and Bioanalytical Electrochemistry, vol. 1, pp. 169–187, 2009. View at Google ScholarJ. N. Mohanasundararaju, R. Sivasubramanian, and N. Alagumurthi, “Optimisation of work roll grinding using Response Surface Methodology and evolutionary algorithm,” International Journal of Manufacturing Research, vol. 3, no. 2, pp. 236–251, 2008. View at Publisher · View at Google Scholar · View at ScopusA. Pandey, P. Nigam, C. R. Soccol, V. T. Soccol, D. Singh, and R. Mohan, “Advances in microbial amylases,” Biotechnology and Applied Biochemistry, vol. 31, no. 2, pp. 135–152, 2000. View at Google Scholar · View at ScopusB. Chauhan and R. Gupta, “Application of statistical experimental design for optimization of alkaline protease production from Bacillus sp. RGR-14,” Process Biochemistry, vol. 39, no. 12, pp. 2115–2122, 2004. View at Publisher · View at Google Scholar · View at ScopusC. Tari, H. Genckal, and F. Tokatli, “Optimization of a growth medium using a statistical approach for the production of an alkaline protease from a newly isolated Bacillus sp. L21,” Process Biochemistry, vol. 41, no. 3, pp. 659–665, 2006. View at Publisher · View at Google Scholar · View at ScopusN. Fakhfakh-Zouari, A. Haddar, N. Hmidet, F. Frikha, and M. Nasri, “Application of statistical experimental design for optimization of keratinases production by Bacillus pumilus A1 grown on chicken feather and some biochemical properties,” Process Biochemistry, vol. 45, no. 5, pp. 617–626, 2010. View at Publisher · View at Google Scholar · View at ScopusF. S. Luciana and H. H. Sato, “Production of alkaline protease from cellulosimicrobium cellulans,” Brazilian Journal of Microbiology, vol. 40, no. 1, pp. 54–60, 2009. View at Google Scholar · View at ScopusS. Negi and R. Banerjee, “Amylase and protease production from A. Awamori,” Food Technology and Biotechnology, vol. 44, pp. 257–261, 2006. View at Google ScholarT. Y. Wu, A. W. Mohammad, J. M. D. Jahim, and N. Anuar, “Optimized reuse and bioconversion from retentate of pre-filtered palm oil mill effluent (POME) into microbial protease by Aspergillus terreus using response surface methodology,” Journal of Chemical Technology and Biotechnology, vol. 84, no. 9, pp. 1390–1396, 2009. View at Publisher · View at Google ScholarJ. P. van den Hombergh, M. D. Sollewijn Gelpke, P. J. I. Van De Vondervoort, F. P. Buxton, and J. Visser, “Disruption of three acid proteases in Aspergillus niger—effects on protease spectrum, intracellular proteolysis, and degradation of target proteins,” European Journal of Biochemistry, vol. 247, no. 2, pp. 605–613, 1997. View at Google Scholar · View at ScopusK. S. Vishwanatha, A. G. Appu Rao, and S. A. Singh, “Characterisation of acid protease expressed from Aspergillus oryzae MTCC 5341,” Food Chemistry, vol. 114, no. 2, pp. 402–407, 2009. View at Publisher · View at Google Scholar · View at ScopusM. Kolaczkowska, “Aspartic proteinase from Penicillium camemberti: purification, properties, and substrate specificity,” Enzyme and Microbial Technology, vol. 17, no. 8, pp. 719–724, 1995. View at Publisher · View at Google ScholarS. Kumar, N. S. Sharma, M. R. Saharan, and R. Singh, “Extracellular acid protease from Rhizopus oryzae: purification and characterization,” Process Biochemistry, vol. 40, no. 5, pp. 1701–1705, 2005. View at Publisher · View at Google Scholar · View at ScopusF. M. Olajuyigbe, J. O. Ajele, and T. L. Olawoye, “Some physicochemical properties of acid protease produced during growth of Aspergillus niger (NRRL 1785),” Global Journal of Pure and Applied Science, vol. 9, pp. 523–528, 2003. View at Google ScholarL. C. Wu and Y. D. Hang, “Purification and characterization of acid proteinase from Neosartorya fischeri var. spinosa IBT 4872,” Letters in Applied Microbiology, vol. 27, no. 2, pp. 71–75, 1998. View at Google Scholar · View at ScopusH. Hashimoto, T. Iwaasa, and T. Yokotsuka, “Some properties of acid protease from the thermophilic fungus, Penicillium duponti K1014,” Applied Microbiology, vol. 25, no. 4, pp. 578–583, 1973. View at Google Scholar · View at ScopusA. M. Hashem, “Optimization of milk-clotting enzyme productivity by Penicillium oxalicum,” Bioresource Technology, vol. 70, no. 2, pp. 203–207, 1999. View at Publisher · View at Google Scholar · View at ScopusM. Alessandro and F. Federico, “Partial purification and characterization of a yeast extracellular acid protease,” Journal of Dairy Science, vol. 63, no. 9, pp. 1397–1402, 1980. View at Google Scholar · View at ScopusH. Zhu, D. C. Guo, and B. P. Dancik, “Purification and characterization of an extracellular acid proteinase from the ectomycorrhizal fungus Hebeloma crustuliniforme,” Applied and Environmental Microbiology, vol. 56, no. 4, pp. 837–843, 1990. View at Google Scholar · View at ScopusG. A. Somkuti and F. J. Babel, “Purification and properties of Mucor pusillus acid protease,” Journal of Bacteriology, vol. 95, no. 4, pp. 1407–1414, 1968. View at Google Scholar · View at ScopusD. E. J. W. Basten, J. Visser, and P. J. Schaap, “Lysine aminopeptidase of Aspergillus niger,” Microbiology, vol. 147, no. 8, pp. 2045–2050, 2001. View at Google Scholar · View at ScopusM. Monod, S. Capoccia, B. Léchenne, C. Zaugg, M. Holdom, and O. Jousson, “Secreted proteases from pathogenic fungi,” International Journal of Medical Microbiology, vol. 292, no. 5-6, pp. 405–419, 2002. View at Google Scholar · View at ScopusK. Gomi, K. Arikawa, N. Kamiya, K. Kitamoto, and C. Kumagai, “Cloning and nucleotide sequence of the acid protease-encoding gene (pepA) from Aspergillus oryzae,” Bioscience, Biotechnology, and Biochemistry, vol. 57, no. 7, pp. 1095–1100, 1993. View at Google Scholar · View at Scopus