Multicell multiuser massive MIMO channel estimation and MPSK signal block detection applying two-dimensional compressed sensing

EURASIP Journal on Wireless Communications and Networking, Oct 2018

For the uplink multicell massive multiple-input multiple-output (MIMO) block fading systems, a two-dimensional smoothed l0 channel estimation method (2D-SL0-CE) with the aid of virtual channel representation is firstly exploited in this paper, which can jointly estimate the desired multiuser channels of the target cell and the interference links from neighbor cells without inducing pilot contamination. Then, a 2D-SL0 signal detection method (2D-SL0-SD) with the aid of sparse decomposing and the modified 2D sl0 recovery algorithm is proposed, which can jointly decode M-ary phase-shift keying (MPSK) signal block for whole desired users. Moreover, an improved 2D-SL0-SD is also proposed to remove multiuser interference of neighbor cells in high SNR scenario. Simulation results show that the 2D-SL0-CE method can remove performance floor induced by pilot contamination and need less pilot overhead than the conventional least square (LS) method. When detecting QPSK signal blocks at 12 dB SNR, the 2D-SL0-SD method with perfect channel state information (CSI) can obtain 10−2 BER. Moreover, in the case of 8PSK signals, the 2D-SL0-SD joining with the 2D-SL0-CE can obtain 10−2 BER at 20 dB SNR.

A PDF file should load here. If you do not see its contents the file may be temporarily unavailable at the journal website or you do not have a PDF plug-in installed and enabled in your browser.

Alternatively, you can download the file locally and open with any standalone PDF reader:

https://link.springer.com/content/pdf/10.1186%2Fs13638-018-1252-9.pdf

Multicell multiuser massive MIMO channel estimation and MPSK signal block detection applying two-dimensional compressed sensing

EURASIP Journal on Wireless Communications and Networking December 2018, 2018:238 | Cite as Multicell multiuser massive MIMO channel estimation and MPSK signal block detection applying two-dimensional compressed sensing AuthorsAuthors and affiliations Xinrong YeAiqing ZhangGan ZhengLi YouXiqi Gao Open Access Research First Online: 11 October 2018 218 Downloads Part of the following topical collections:Ultra-Reliable-and-Available Low-Latency Communications for 5G/B5G-enabled IoT Abstract For the uplink multicell massive multiple-input multiple-output (MIMO) block fading systems, a two-dimensional smoothed l0 channel estimation method (2D-SL0-CE) with the aid of virtual channel representation is firstly exploited in this paper, which can jointly estimate the desired multiuser channels of the target cell and the interference links from neighbor cells without inducing pilot contamination. Then, a 2D-SL0 signal detection method (2D-SL0-SD) with the aid of sparse decomposing and the modified 2D sl0 recovery algorithm is proposed, which can jointly decode M-ary phase-shift keying (MPSK) signal block for whole desired users. Moreover, an improved 2D-SL0-SD is also proposed to remove multiuser interference of neighbor cells in high SNR scenario. Simulation results show that the 2D-SL0-CE method can remove performance floor induced by pilot contamination and need less pilot overhead than the conventional least square (LS) method. When detecting QPSK signal blocks at 12 dB SNR, the 2D-SL0-SD method with perfect channel state information (CSI) can obtain 10−2 BER. Moreover, in the case of 8PSK signals, the 2D-SL0-SD joining with the 2D-SL0-CE can obtain 10−2 BER at 20 dB SNR. KeywordsMassive MIMO Sparse channel estimation Data block detection Two-dimensional smoothed l0 (2D-SL0)  Abbreviations 2D-SL0 Two-dimensional smoothed l0 2D-SL0-CE Two-dimensional smoothed l0-norm channel estimation 2D-SL0-SD Two-dimensional smoothed l0-norm signal detection 2D-SL0-SD-IC Two-dimensional smoothed l0-norm signal detection with interference cancel BER Bit error rate BS Base station CS Compressed sensing CSI Channel state information FDD Frequency division duplexing JSDM Joint spatial division and multiplexing LS Least square MIMO Multiple-input multiple-output ML Maximum likelihood MMSE Minimal mean square error MPSK M-ary phase-shift keying NMSE Normalized mean square error QPSK Quadrature phase-shift keying SNR Signal-to-noise ratio TDD Time division duplexing ULA Uniform linear array 1 Introduction The high energy and spectrum efficiency of massive multiple-input multiple-output (MIMO) systems heavily build on the premise that the base stations (BS) obtain channel state information (CSI) with reasonable quality, which is generally estimated via pilot sequences [1]. However, in the uplink massive MIMO systems, the pilot overhead demanded should be proportional to the number of users and would be prohibitively large as the number of users increase. In the uplink multicell massive MIMO, this results in pilot contamination as the same pilot sequences have to be reused by neighbor cells to serve a large number of users [2]. Moreover, the pilot contamination is a major limiting factor to system performance [3]. Hence, the massive MIMO urgently needs efficient channel estimation scheme without producing pilot contamination and requiring too much pilot overhead. Based on the estimated CSI, the signals received at base stations are typically detected through linear methods with low complexity, such as zero-forcing [4, 5, 6] and matched filter [7, 8]. However, the performances of linear detector are typically far inferior to the optimal maximum likelihood (ML) detector whose computational complexity exponentially scales up with the signal constellation size and the number of antennas [9]. Thus, the development of computationally efficient and reliable detector for massive MIMO also needs to be thoroughly addressed [10]. In the past few years, several types of schemes have been exploited to mitigate or reduce the impact of pilot contamination in multicell massive MIMO systems. (1) Semi-blind or blind approaches, such as [11, 12, 13, 14]—the eigenvalue decomposition-based method with a short training sequence was proposed in [11]. Hu et al. [12] proposed a semi-blind method without requiring the statistical information of channels. Another low-complexity semi-blind approach was proposed in [13], which the received signal are firstly projected onto the subspace with minimal interference, then alternatively refined the channel estimation and detected the data symbols. Applying the theory of large random matrices, [14] proposed a blind pilot decontamination with subspace projection. (2) Optimization design of non-orthogonal pilot signals, such as [15, 16, 17, 18]—when training slots are not large enough to construct the orthogonal pilot signals, [15] exploits a pilot design criterion and shows that the line packing on a complex Grassmannian manifold is the optimization scheme, which is based on minimal mean square error (MMSE) estimator. A generalized Welch-bound equality-based pilot signal design method is proposed in [16], which has low correlation coefficients and ensures the network to satisfy the requirement of user capacity. For a given pilot length, [17] proposes an alternating minimization-based pilot design algorithm. (3) The precoding-based approaches, such as [19, 20, 21]—a MMSE-based precoding is exploited in [19] to alleviate the impact of pilot contamination. A pilot contamination mitigation method along with zero-forcing precoding is proposed in [20], which can generate orthogonal pilot signals across neighboring cells through multiplying the Zadoff-Chu sequences element-wise with a specific orthogonal variable spreading factor code. Some significant efforts have been made to reduce the pilot overhead for massive MIMO systems, which can be divided into two broad categories. (1) Low-rank channel covariance matrices based methods, such as [22, 23, 24]—the finite scattering environment and small angular spread result in high correlation of different paths between the user and the BS [25, 26, 27, 28, 29] and low-rank channel covariance matrix. Through exploiting the correlation characteristic of channel vectors, the joint spatial division and multiplexing (JSDM) was proposed in [23] which significantly reduced the overhead of downlink training and uplink feedback for frequency division duplexing (FDD) massive MIMO systems. When the number of pilot signals is no less than the rank of channel covariance matrix and the noise interference disappear, [24] proves that the MMSE estimator can recovery channel vectors exactly. (2) Compressed channel sensing method—exploiting the channel sparsity and applying the compressed sensing (CS) to reduce the overhead of CSI feedback has been investigated in [30, 31, 32]. A spare channel estimation method applying Gaussian-mixture Bayesian learning has been proposed in [33] to estimate the whole channel parameters including the desired and interference links, which can mitigate pilot contamination and reduce pilot overhead, but every time, the approach just can estimate the channel response at one beam. An iterative MIMO detector with relaxed ML constraints using sparse decomposition has been proposed to preserve a low computational cost even increase the signal size, but the method just suit to detect a vector [34]. In block fading systems, the detection target at the BS usually is a multiuser data frame, i.e., a two-dimensional (2D) signal block. To detect the 2D signals, the method in [34] should run the decoding process many times or convert the 2D signal detection problem to a vector detection problem. However, the converting method will substantially increase the required memory and processing load which would make it become non-competitive when applied to massive MIMO block fading systems. For example, the converting approach can be represented as: $$ \mathbf{Y}=\mathbf{AXB}^{T} \Longleftrightarrow \mathbf{y}=\Phi \mathbf{x} $$ (1) with A∈R60×200, B∈R30×100, x=vec(X), and y=vec(Y), which results in Φ=B⊗A with dimensions 1800×20,000. The signs of vec() and \(\bigotimes \) denote vectorization of a matrix and Kronecker product, respectively. In this paper, the multiuser channel estimation problem and the multiuser signal decoding problem in uplink massive MIMO systems are modelled as two-dimensional sparse signal recovery problems in compressed sensing, respectively. Although [35, 36] researched the 2D compressed sensing channel estimation schemes for massive MIMO, it is the FDD model discussed in [35, 36] which is different from the time division duplexing (TDD) multicell multiuser system model considered in this paper. The main contributions of this paper are summarized as follows: We propose a channel estimation method named as 2D-SL0-CE applying the two-dimensional smoothed l0-norm compressed sensing recovery algorithm [37, 38], which are able to jointly estimate multiuser CSI. Using virtual channel representation, the 2D-SL0-CE formulates the joint channel estimation problem, comprising both the target and interference channels, as a 2D sparse signal reconstruction problem in CS, which not only can mitigate the pilot contamination but also can significantly reduce pilot overhead. We propose a signal detection method named as 2D-SL0-SD using our modified 2D-SL0 algorithm, which can decode multiuser M-ary phase-shift keying (MPSK) signal block. Applying sparse decomposition, the 2D-SL0-SD models the detection problem of multiuser signal block as a 2D sparse signal reconstruction problem whose elements are binaries {0,1}. Moreover, in the high SNR scenario, through exploiting the estimated CSI of interference links, an improved 2D-SL0-SD is also proposed to remove the decoding bottleneck induced by interference from neighboring cells. The remaining paper is organized as follows. The system model and the least square (LS) channel estimation methods are described in Section 2. Section 3 models the multicell multiuser channel estimation problem as a two-dimensional compressed sensing problem and describes the proposed channel estimation algorithm. Section 4 models the signal decoding problem of multiuser as a 2D sparse signal recovery problem and presents the steps of the proposed 2D-SL0-SD method. Section 5 gives and analyzes the numerical results. Section 6 draws a conclusion of the whole paper. Notations: diag(x) represents a diagonal matrix with diagonal elements being the vector x. Superscripts T and † denote the transpose and pseudo-inverse, respectively. CN(0,1) denotes complex Gaussian variables with zero mean and unit variance. \(\bigotimes \) denotes Kronecker product. Vectors and matrices are denoted by boldface lowercase and uppercase letters, respectively. 2 System model Consider a multicell massive MIMO system in which each target cell shares the same frequency band with L−1 adjacent cells. Each cell has one BS with a uniform linear array (ULA) of M antennas that serves K (K<<M) single antenna users. The uplink channel vector from the kth terminal in ith cell to jth BS is modelled as: $$ \mathbf{h}_{jik}=\sqrt{\beta_{jik}}\mathbf{g}_{jik}, $$ (2) where gjik is the fast fading vector, and large-scale fading factor βjik describes the quasi-static shadow fading and the path loss. Different channel vectors are assumed to be independent. Consequently, the channel matrix between the K users in ith cell and the jth BS can be represented as: $$ \mathbf{H}_{ji}\mathbf{=G}_{ji}\mathbf{D}_{ji} $$ (3) with Hji=[hji1,⋯,hjiK], Gji=[gji1,⋯,gjiK] and \(\mathbf {D}_{ji}=\text {diag}\left (\sqrt {\beta _{ji1}},\cdots,\sqrt {\beta _{jiK}}\right)\). In a block fading channel, the training signal received at the jth BS becomes: $$ \mathbf{Y}_{j}^{tr}=\sqrt{P_{tr}}\sum\limits_{i=1}^{L}\mathbf{H}_{ji}\mathbf{X}_{i}^{tr}+\mathbf{N}_{j}^{tr}, $$ (4) where Ptr denotes the training signal-to-noise ratio (SNR), the rows of \(\mathbf {X}_{i}^{tr}\in C^{K\times T_{tr}}\) are the pilot sequences of ith cell, and \(\mathbf {N}_{j}^{tr}\) is the noise with i.i.d. elements distributed as CN(0,1). The jth cell is assumed as the target cell. One natural choice to find a channel estimate based on the training signal without employing any prior information is the LS method which is given by: $$\begin{array}{*{20}l} \hat{\mathbf{H}}_{jj}^{LS}&=\frac{1}{\sqrt{P_{tr}}}\mathbf{Y}_{j}^{tr}\left(\mathbf{X}_{j}^{tr}\right)^{\dag} \\ &= \mathbf{H}_{jj}+\sum\limits_{i=1,i\neq j}^{L} \mathbf{H}_{ji}+\frac{1}{\sqrt{P_{tr}}}\mathbf{N}_{j}^{tr}, \end{array} $$ (5) where the second term denotes pilot contamination resulting in the same orthogonal pilots reused by adjacent cells. 3 2D-SL0-CE channel estimation method The key idea of our exploited channel estimation is to explore the sparsity in the virtual channel representation, which applies spatial beams at fixed virtual directions to characterize the physical channel matrix. The virtual channel matrix \(\mathbf {G}_{ji}^{v}\) can be linked to the above described physical channel matrix Gji by the following transformation: $$ \mathbf{G}_{ji}=\mathbf{A}_{R}\mathbf{G}_{ji}^{v}, $$ (6) where AR=[aR(θ1),⋯,aR(θM)] with the receiver response vectors given by: $$ \mathbf{a}_{R}(\theta_{m})=\frac{1}{\sqrt{M}}\left[1, e^{-j2\pi \theta_{m}}, \cdots, e^{-j2\pi(M-1)\theta_{m}}\right]^{T}. $$ (7) The direction θm is related to the physical angle ϕm∈[−π/2,π/2] as θm=dsin(ϕm)/λ with λ being the carrier wavelength and d being the antenna spacing [39]. We uniformly sample the principal θ period to set the virtual spatial angles, i.e., θm=m/M, and resulting in an M×M unitary discrete Fourier transform matrix AR. The element \(\mathbf {G}_{ji,mk}^{v}\) of M×K matrix \(\mathbf {G}_{ji}^{v}\) represents the coupling gain from the kth terminal to the mth virtual receive angle θm. Therefore, the element will be zero when there is no corresponding coupling, and the \(\mathbf {G}_{ji}^{v}\) will be a sparse matrix when the number of non-zero elements is much smaller than that of the total elements. Substituting (6) into (4) yields the following received training signal at the jth BS: $$ \mathbf{Y}_{j}^{tr}=\sqrt{P_{tr}}\sum_{i=1}^{L}\mathbf{A}_{R}\mathbf{G}_{ji}^{v} \mathbf{D}_{ji}\mathbf{X}_{i}^{tr}+\mathbf{N}_{j}^{tr}. $$ (8) Furthermore, taking the transpose operation to (8), we can obtain: $$ {{} \begin{aligned} \underbrace{\frac{1}{\sqrt{P_{tr}}}(\mathbf{Y}_{j}^{tr})^{T}}_{=\mathbf{Y}} \,=\,\sum\limits_{i=1}^{L}\left(\mathbf{X}_{i}^{tr}\right)^{T}\mathbf{D}_{ji}\left(\mathbf{G}_{ji}^{v}\right)^{T}\mathbf{A}_{R}\,+\,\frac{1}{\sqrt{P_{tr}}}\left(\mathbf{N}_{j}^{tr}\right)^{T}\\ =\![\underbrace{\left(X_{1}^{tr}\right)^{T},\!\cdots\!,\left(X_{L}^{tr}\right)^{T}}_{=\mathbf{X}}] \underbrace{\left[\begin{array}{l} \mathbf{D}_{j1}\left(\mathbf{G}_{j1}^{v}\right)^{T} \\ \vdots\\ \mathbf{D}_{jL}\left(\mathbf{G}_{jL}^{v}\right)^{T} \end{array}\right]}_{=\mathbf{G}} \!\mathbf{A}_{R}\,+\,\underbrace{\frac{1}{\sqrt{P_{tr}}}\left(\mathbf{N}_{j}^{tr}\right)^{T}}_{=\mathbf{N}}. \end{aligned}} $$ (9) Now, based on the linear model Y=XGAR+N, the channel estimation problem is modelled as a 2D sparse signal reconstruction problem in compressed sensing. Then, we estimate Hj=[Hj1,⋯,HjL] based on Y, X, and AR, using the 2D-SL0 sparse reconstruction algorithm [38]. The proposed channel estimation method 2D-SL0-CE is summarized in Algorithm 1. Different from other types of compressed sensing recovery algorithms, the SL0 and 2D−SL0 applied the following function to approximate the l0-norm of b, i.e., ||b||0. $$ \left \{ \begin{array}{lr} \mathbf{F}_{\sigma}(\mathbf{b})=\sum_{i=1}^{M} \text{exp}\left(\frac{-b_{i}^{2}}{2\sigma^{2}}\right),\\ ||\mathbf{b}||_{0}\approx M-\mathbf{F}_{\sigma}(\mathbf{b}),\sigma\rightarrow 0, \end{array} \right. $$ (10) where b∈RM×1 is a sparse vector, and the parameter σ determines the quality of the approximation and how smooth the function Fσ(b). Consequently, the minimum l0-norm solution can be found by maximizing Fσ(b). In Algorithm 1, steps 2–9 gradually decrease the value of σ and maximize the objective function for each value of σ. Open image in new window 4 2D-SL0-SD signal detection method In a block fading scenario, the received data signal at the jth BS can be written as: $$ \mathbf{Y}_{j}=\sqrt{P_{\text{data}}}\mathbf{H}_{jj}\mathbf{X}_{j}+\underbrace{\sqrt{P_{\text{data}}}\sum\limits_{i=1,i\neq j}^{L}\mathbf{H}_{ji}\mathbf{X}_{i}+\mathbf{N}_{j}}_{=\mathbf{W}_{j}}, $$ (11) where \(\mathbf {Y}_{j}\in \mathcal {C}^{M\times N}\) is the received data, \(\sqrt {P_{\text {data}}}\) denotes the uplink SNR, Xi denotes the transmitted data matrix of the ith cell whose element is selected from a finite alphabet constellation defined as {s1,⋯,sQ} with Q being the finite alphabet cardinal, Nj is the noise with elements distributed as CN(01), and Wj represents the noise plus interference faced by the received data of jth BS. The transmitted symbol of the ith cell can be sparse represented as (12) through exploiting the prior knowledge that each transmitted element Xi,mn belongs to a discrete and finite alphabet constellation: $$ X_{i,mn}=\mathbf{s e}_{i,mn}, $$ (12) where Xi,mn denotes the nth symbol of mth user in ith cell, s=[s1,⋯,sQ] is the discrete and finite constellation vector, and ei,mn=[ei,mn(s1),⋯,ei,mn(sQ)]T with ei,mn(sq) being equal to 1 if Xi,mn=sq or 0 otherwise (1≤q≤Q). Applying this sparse representation into all symbols, the transmitted data matrix in the ith cell can be expressed in function of a sparse matrix as: $$ \mathbf{X}_{i}=\mathbf{B}_{s}\mathbf{E}_{i}, $$ (13) where \(\mathbf {B}_{s}=\mathbf {I}_{K} \bigotimes \mathbf {s}\) is a block diagonal matrix of size K×KQ, and the nth column of the matrix Ei is [(ei,1n)T,⋯,(ei,Kn)T]T. Substituting (13) into (11) generates $$ \mathbf{Y}_{j}=\sqrt{P_{\text{data}}}\mathbf{H}_{jj}\mathbf{B}_{s}\mathbf{E}_{j}+\mathbf{W}_{j}=\mathbf{A}_{j}\mathbf{E}_{j}\mathbf{I}_{N}+\mathbf{W}_{j} $$ (14) with \(\mathbf {A}_{j}=\sqrt {P_{\text {data}}}\mathbf {H}_{jj}\mathbf {B}_{s}\). The detection problem of signal block has been modelled as a 2D sparse binary {0,1} reconstruction problem in CS, then based on Yj, Aj, and IN, the signal block Xj can be detected using the modify 2D-SL0 algorithm which suits to reconstruct 2D sparse binary {0,1} signal. The process of 2D-SL0-SD is summarized in Algorithm 2. Because the elements of Ej needed to be recovered are 0 or 1, but the elements recovered by the original 2D-SL0 algorithm are not exactly 0 or 1, step 10 of Algorithm 2 is added to find which element of \(\hat {\mathbf {e}}_{j,mn}\) maybe 1 with highest probability and reset such element to 1 and others to 0. Open image in new window In the high SNR scenario, such as Nj→0, it can be observed from (11) that the main factor restricting the decoding performance is not the noise but the interference from neighboring cells. Thus, the performance of 2D-SL0-SD will meet floor as the SNR increases. In order to resolve this problem, the CSI of interference links are exploited and an improved 2D-SL0-SD method is proposed, which does not treat the signals from neighbor cells as interference, moreover, decodes them jointly with the desired signals. Specifically, exploiting the CSI of whole links estimated by the above proposed 2D-SL0-CE method, the received data signal at the jth BS in (11) can be rewritten as: $$\small \mathbf{Y}_{j}=\sqrt{P_{\text{data}}}[\mathbf{H}_{j1},\!\cdots\!, \mathbf{H}_{jL}][(\mathbf{X}_{1})^{T},\!\cdots\!, (\mathbf{X}_{L})^{T}]^{T}+\mathbf{N}_{j}. $$ (15) Moreover, substituting (13) into (15) can generate: $$ \begin{aligned} \mathbf{Y}_{j}\,=\, &\underbrace{\sqrt{P_{\text{data}}}[\mathbf{H}_{j1}\mathbf{B}_{s},\cdots\!, \mathbf{H}_{jL}\mathbf{B}_{s}]}_{=\mathbf{A}}\underbrace{[(\mathbf{E}_{1})^{T},\cdots\!, (\mathbf{E}_{L})^{T}]^{T}}_{=\mathbf{E}}\!\mathbf{I}_{N} \\ &+\mathbf{N}_{j}. \end{aligned} $$ (16) Now, the decoding problem without multiuser interference has also been modelled as a 2D sparse {0,1} signal reconstruction problem, which has the same form as that of (14), and can be solved through the processes of Algorithm 2 whose Aj needs to be replaced by A. Hereafter, the improved 2D-SL0-SD with interference cancel is named as 2D-SL0-SD-IC. Comparing (16) with (14), it can be observed that the recovery object of the 2D-SL0-SD-IC is E, including not only the Ej of the objective cell but also the Ei of the L−1 neighbor cells (i=1,⋯L,i≠j), and the noise is the only interference source. It is worth noting that the proposed 2D-SL0-SD is only suitable to decode constant modulus signal, such as MPSK. Since there is only one element of ei,mn in (12) equaling to 1 and the others are zeros, Algorithm 2 needs a ruler to reset the values of the estimated \(\hat {\mathbf {e}}_{i,mn}\). In step 10 of Algorithm 2, the ruler is that the element of \(\hat {\mathbf {e}}_{j,mn}\) with the largest real part is viewed as such element whose value is 1 with the highest probability. Such ruler requires that the elements of s in (12) have the same modulus. 5 Numerical results and discussion The spectral efficiency and estimation accuracy of the proposed 2D-SL0-CE sparse channel estimation method and the decode performance of the proposed 2D-SL0-SD are investigated. A multicell scenario with L cells sharing the same frequency band is considered. The fading coefficient is modelled as βjik=zjik/(rjik/rh)α, in which \(z_{jik}\thicksim ln N\left (0,\sigma _{\text {shadow}}^{2}\right)\) is a lognormal random variable, rjik denotes the distance between the BS and the corresponding terminal, and rh is the cell-hole radius. The number of non-zero elements in each column of \(G_{ji}^{v}\), which means the number of multipath, is assumed to S, whose positions are randomly selected and values are generated through CN(0,1). The pilot sequence of each user is randomly generated using the complex normal distribution and then is normalized to unity. The normalized mean square error (NMSE) defined as \(\frac {1}{N_{\text {MC}}}{\sum \nolimits }_{i=1}^{N_{\text {MC}}}\frac {\|\hat {H_{i}}-H_{i}\|_{F}^{2}}{\|H_{i}\|_{F}^{2}}\) is used to evaluate the estimation accuracy, where NMC means the number of Monte-Carlo simulations, Hi and \(\hat {H_{i}}\) are the actual and estimated channel impulse response of ith Monte-Carlo trial, respectively. The parameters of the system and the 2D-SL0 algorithm are summarized in Table 1. Table 1 System and algorithm parameter values Parameters Values Parameters Values Number of BS antennas M 256 Standard deviation σshadow 8 dB Number of cells L 7 Threshold value σmin 10−4 Cell radius R 1000 m Descent factor ρ 0.6 Cell-hole radius rh 50 m Step size μ 2 Path loss exponent α 3.5 Number of iterations P 3 Number of users in each cell K 20 Number of simulations NMC 1000 Firstly, at the scenario of S=5, the NMSE of the 2D-SL0-CE and the bit error rate (BER) of the 2D-SL0-SD detection QPSK signals with various CSI, including perfect and estimated CSI, are investigated. The whole number of multicell users is 20×7=140; thus, the LS method should require orthogonal pilot sequences with length being not less than 140 to avoid pilot contamination. Figure 1 shows that the 2D-SL0-CE method applying random pilot sequences with a length of 12 can outperform LS with 140 pilots nearly 5 dB. Moreover, the NMSE of 2D-SL0-CE is approximate linear reducing with the SNR increasing when the pilot length is not less than 12. While in the case that 20 orthogonal pilot sequences are reused by the objective cell and neighbor cells, Fig. 1 also shows that the LS method will meet a performance floor caused by pilot contamination. In a block fading scenario with signal length N=200, Fig. 2 plots the BER performance of the 2D-SL0-SD detection QPSK signal block using various CSIs. Applying perfect CSI at 10 dB SNR, the 2D-SL0-SD can approach near to 10−2 BER. Moreover, its BER is approximate linear reducing with the SNR increasing, which shows its reliable detection ability. Using the CSI estimated through the 2D-SL0-CE, where each user applies random non-orthogonal pilot sequence with length being 32, the obtained BER of 2D-SL0-SD at 15 dB SNR is slightly better than 10−2, which shows joint the 2D-SL0-CE with 2D-SL0-SD for channel estimation and decoding QPSK signals is a feasible scheme. Open image in new window Fig. 1 NMSE performance of 2D-SL0-CE and LS methods Open image in new window Fig. 2 BER performance of 2D-SL0-SD with various CSIs Then, applying perfect CSI and estimated CSI through 2D-SL0-CE, respectively, Figs. 3 and 4 show the BER of 2D-SL0-SD and its improved version 2D-SL0-SD-IC detecting various PSK data block with length N=200. In both cases, the BER of 2D-SL0-SD is better than 2D-SL0-SD-IC within a SNR threshold value. This is because the received energy of interference data is usually smaller than that of target data, which induces more difficult to decode interference data. The decoding object in 2D-SL0-SD-IC includes the target and interference data, which means the decoding result of two parts will affect each other. Thus, in the low-SNR scenario, the low correct decoding probability of interference data leads to 2D-SL0-SD-IC has higher BER than 2D-SL0-SD. With the SNR increasing and exceeding a threshold value, the 2D-SL0-SD will gradually meet a performance bound induced by interference. However, the BER of 2D-SL0-SD-IC will be still approximately linear reducing owing to gradually high correct decoding probability of interference data. In theory, with the distance of the two neighbor signal points in constellation diagram gradually reducing, it will be more difficult to decode the signals correctly. In Figs. 3 and 4, it can be observed that the BERs of QPSK, 8PSK, and 16PSK are gradually increasing at the same SNR. Open image in new window Fig. 3 BER of 2D-SL0-SD with perfect CSI Open image in new window Fig. 4 BER of 2D-SL0-SD joint with 2D-SL0-CE Finally, the NMSE of 2D-SL0-CE method with fixed pilot length at various scenarios, including various sparsity and number of users in each cell, is studied in Figs. 5 and 6, respectively. In the case of each cell having 20 users, applying random pilot sequences with fixed length of 26, Fig. 5 shows that the NMSE is approximately linear reducing with the SNR increasing when the S is not larger than 20. In the case of S=5 and pilot length being 26, Fig. 6 shows that the NMSE is approximately linear reducing with the SNR increasing when the number of users in each cell is not larger than 50. In order to recovery a 1D E-sparse F-length vector successfully with high probability, [40] presents that the number of measurements needed is of order \(\mathcal {O}(E\text {log}(F/E))\). In the 2D cases, from the best performance plots in Figs. 5 and 6, it can be obtained that the number of measurements are 2.15 and 2.23 times of KLSlog(M/S), respectively, where the value of KLS is the number of non-zero elements in 2D signals. Thus, ensuring the original 2D signal can be recovered with high probability, the number of measurements needed is also of order \(\mathcal {O}(E\text {log}(F/E))\), where the E and F denote the numbers of non-zero elements and whole elements in the 2D signal, respectively. In practical, the above ruler can be used to guide for setting pilot length. Open image in new window Fig. 5 NMSE of 2D-SL0-CE with various channel sparsity Open image in new window Fig. 6 NMSE of 2D-SL0-CE with various numbers of users 6 Conclusions This paper has investigated the two challenging problems for block fading massive MIMO systems. The one is to exploit efficient uplink channel estimation method that requires acceptable pilot overhead and can mitigate pilot contamination. The other one is to jointly decode multiuser data block. The joint multiuser channel estimation and data block detection problems have both been modelled and solved as a 2D sparse signal reconstruction problem in the CS framework. More specifically, through using a linear virtual channel representation for ULA, the 2D-SL0-CE compressed channel sensing method is proposed, which needs less pilot overhead than LS method, and can jointly estimate the desired and interference uplinks. Through sparse representation in a finite alphabet set for each transmitted data symbol, the 2D-SL0-SD data decoding method is proposed which can simultaneously decode a MPSK data block for multiuser. Simulation results demonstrate that joint the 2D-SL0-CE with 2D-SL0-SD to estimate channel and decode MPSK data for multiuser massive MIMO is a feasible scheme. Notes Funding This work was partly supported by the National Natural Science Foundation of China (Grant Nos. 61601005, 61801114), Natural Science Foundation of Anhui Province (Grant Nos. 1808085MF164, 1608085QF138), Key Projects of the Outstanding Young Talents Program in the Universities of Anhui Province (Grant No. gxyqZD2016027), the Natural Science Foundation of Jiangsu Province (Grant No. BK20170688) and Doctoral Scientific Research Foundation of Anhui Normal University (Grant Nos. 2014bsqdjj38, 2018XJJ40). Availability of data and materials Mostly, I got the writing material from different journals as presented in the references. A MATLAB tool has been used to simulate my concept. Authors’ contributions XY conceived and designed the methods. XY performed the experiments and wrote the paper. AZ analyzed the simulation data. GZ and XG gave valuable suggestions on the structure of the paper. LY revised the original manuscript. All authors read and agreed the manuscript. Competing interests The authors declare that they have no competing interests. Publisher’s Note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations. References 1. N. Shariati, E. Bjornson, M. Bengtsson, M. Debbah, Low-complexity polynomial channel estimation in large-scale MIMO with arbitrary statistics. IEEE J. Sel. Top. Signal Proc.8(5), 815–830 (2014).CrossRefGoogle Scholar 2. O. Elijah, C.Y. Leow, T.A. Rahman, S. Nunoo, S.Z. Iliya, A comprehensive survey of pilot contamination in massive MIMO 5G system. IEEE Commun. Surv. Tutor.18(2), 905–923 (2016).CrossRefGoogle Scholar 3. H.Q. Ngo, E.G. Larsson, T.L. Marzetta, The multicell multiuser MIMO uplink with very large antenna arrays and a finite-dimensional channel. IEEE Trans. Commun.61(6), 2350–2361 (2013).CrossRefGoogle Scholar 4. W. Tan, M. Matthaiou, S. Jin, X. Li, Spectral efficiency of DFT-based processing hybrid architectures in massive MIMO. IEEE Wirel. Commun. Lett.6(5), 586–589 (2017).CrossRefGoogle Scholar 5. W. Tan, G. Xu, E.D. Carvalho, L. Fan, C. Li, Low cost and high efficiency hybrid architecture massive MIMO systems based on DFT processing. Wirel. Commun. Mob. Comput.2018:, 1–11 (2018).Google Scholar 6. C. Li, K. Song, Y. Li, L. Yang, Energy efficient design for multiuser downlink energy and uplink information transfer in 5G. Sci. China Inf. Sci.59(2), 1–8 (2016).Google Scholar 7. W. Tan, D. Xie, J. Xia, W. Tan, L. Fan, S. Jin, Spectral and energy efficiency of massive MIMO for hybrid architectures based on phase shifters. IEEE Access.6:, 11751–11759 (2018).CrossRefGoogle Scholar 8. W. Tan, S. Jin, C.K. Wen, J. Tao, Spectral efficiency of multi-user millimeter wave systems under single path with uniform rectangular arrays. EURASIP J. Wirel. Commun. Netw.181:, 458–472 (2017).Google Scholar 9. A. Elghariani, M. Zoltowski, Low complexity detection algorithms in large-scale MIMO systems. IEEE Trans. Wirel. Commun.15(3), 1689–1702 (2016).CrossRefGoogle Scholar 10. L. Bai, T. Li, J. Liu, Q. Yu, J. Choi, Large-scale MIMO detection using MCMC approach with blockwise sampling. IEEE Trans. Wirel. Commun.64(9), 3697–3707 (2016).CrossRefGoogle Scholar 11. H.Q. Ngo, E.G. Larsson, EVD-based channel estimation in multicell multiuser MIMO systems with very large antenna arrays (IEEE International Conference on Acoustics, Speech and Signal Processing (ICASSP), Kyoto, 2012).Google Scholar 12. D. Hu, L. He, X. Wang, Semi-blind pilot decontamination for massive MIMO systems. IEEE Trans. Wirel. Commun.15(1), 525–536 (2016).CrossRefGoogle Scholar 13. C.Y. Wu, W.J. Huang, W.H. Chung, Low-complexity semiblind channel estimation in massive MU-MIMO systems. IEEE Trans. Wirel. Commun.16(9), 6279–6290 (2017).CrossRefGoogle Scholar 14. R.R. Muller, L. Cottatellucci, M. Vehkapera, Blind pilot decontamination. IEEE J. Sel. Top. Sign. Process.8(5), 773–786 (2014).CrossRefGoogle Scholar 15. H. Wang, W. Zhang, Y. Liu, Q. Xu, P. Pan, On design of non-orthogonal pilot signals for a multi-cell massive MIMO system. IEEE Wirel. Commun. Lett.4(2), 129–132 (2015).CrossRefGoogle Scholar 16. N. Akbar, N. Yang, P. Sadeghi, R.A. Kennedy, Multi-cell multiuser massive MIMO networks: user capacity analysis and pilot design. IEEE Trans. Commun.64(12), 5064–5077 (2016).CrossRefGoogle Scholar 17. Y. Han, J. Lee, Uplink pilot design for multi-cell massive MIMO networks. IEEE Commun. Lett.20(8), 1619–1622 (2016).CrossRefGoogle Scholar 18. C. Li, K. Song, D. Wang, F. Zheng, L. Yang, Optimal remote radio head selection for cloud radio access networks. Sci. China Inf. Sci.59(10), 1–12 (2016).Google Scholar 19. J. Jose, A. Ashikhmin, T.L. Marzetta, S. Vishwanath, Pilot contamination and precoding in multi-cell TDD systems. IEEE Trans. Wirel. Commun.10(8), 2640–2651 (2011).CrossRefGoogle Scholar 20. S. Ali, Z. Chen, F. Yin, Eradication of pilot contamination and zero forcing precoding in the multi-cell TDD massive MIMO systems. IET Commun.11(13), 2027–2034 (2017).CrossRefGoogle Scholar 21. C. Li, P. Liu, C. Zou, F. Sun, J.M. Cioffi, L. Yang, Spectral-efficient cellular communications with coexistent one- and two-hop transmissions. IEEE Trans. Veh. Technol.65(8), 6765–6772 (2016).CrossRefGoogle Scholar 22. H. Xie, F. Gao, S. Jin, An overview of low-rank channel estimation for massive MIMO systems. IEEE Access. 4:, 7313–7321 (2016).CrossRefGoogle Scholar 23. A. Adhikary, J. Nam, J.Y. Ahn, G. Caire, Joint spatial division and multiplexing the large-scale array regime. IEEE Trans. Inf. Theory.59(10), 6441–6463 (2013).MathSciNetzbMATHCrossRefGoogle Scholar 24. J. Fang, X. Li, H. Li, F. Gao, Low-rank covariance-assisted downlink training and channel estimation for FDD massive MIMO systems. IEEE Trans. Wirel. Commun.16(3), 1935–1947 (2017).CrossRefGoogle Scholar 25. L. Fan, R. Zhao, F. Gong, N. Yang, G.K. Karagiannidis, Secure multiple amplify-and-forward relaying over correlated fading channels. IEEE Trans. Commun.65(7), 2811–2820 (2017).CrossRefGoogle Scholar 26. R. Zhao, Y. Yuan, L. Fan, Y. He, Secrecy performance analysis of cognitive decode-and-forward relay networks in Nakagami-m fading channels. IEEE Trans. Commun.65(2), 549–563 (2017).CrossRefGoogle Scholar 27. L. Fan, X. Lei, N. Yang, T.Q. Duong, G.K. Karagiannidis, Secrecy cooperative networks with outdated relay selection over correlated fading channels. IEEE Trans. Veh. Technol.66(8), 7599–7603 (2017).CrossRefGoogle Scholar 28. X. Wang, H. Zhang, L. Fan, Y. Li, Performance of distributed switch-and-stay combining for cognitive relay networks with primary transceiver. Wirel. Pers. Commun.97(2), 3031–3042 (2017).CrossRefGoogle Scholar 29. J. Yuan, S. Jin, W. Xu, W. Tan, M. Matthaiou, K.K. Wong, User-centric networking for dense C-RANS: high-SNR capacity analysis and antenna selection. IEEE Trans. Commun.65(11), 5067–5080 (2017).CrossRefGoogle Scholar 30. Z. Gao, L. Dai, Z. Wang, S. Chen, Spatially common sparsity based adaptive channel estimation and feedback for FDD massive MIMO. IEEE Trans. Signal Process.63(23), 6169–6183 (2015).MathSciNetzbMATHCrossRefGoogle Scholar 31. V.K.N. Lau, S. Cai, A. Liu, Closed-loop compressive CSIT estimation in FDD massive MIMO systems with 1 bit feedback. IEEE Trans. Signal Process.64(8), 2146–2155 (2016).MathSciNetCrossRefGoogle Scholar 32. C. Li, K. Song, L. Yang, Low computational complexity design over sparse channel estimator in underwater acoustic OFDM communication system. IET Commun.11(7), 1143–1151 (2017).CrossRefGoogle Scholar 33. C.K. Wen, S. Jin, K.K. Wong, J.C. Chen, P. Ting, Channel estimation for massive MIMO using Gaussian-mixture Bayesian learning. IEEE Trans. Wirel. Commun.14(3), 1356–1368 (2015).CrossRefGoogle Scholar 34. Y. Fadlallah, A. Aissa-El-Bey, K. Amis, D. Pastor, R. Pyndiah, New iterative detector of MIMO transmission using sparse decomposition. IEEE Trans. Veh. Technol.64(8), 3458–3464 (2015).CrossRefGoogle Scholar 35. W. Kai, L. Jingzhi, X. Lin, H. Le, Two-dimensional compressed sensing of channel state information in massive MIMO system (IEEE International Conference on Electronics Information and Emergency Communication (ICEIEC), Macau, 2017).Google Scholar 36. Y. Wang, H. Wang, Y. Fu, Modified two-dimensional compressed sensing scheme for massive MIMO channel estimation (IEEE International Conference on Wireless Communications & Signal Processing (WCSP), Yangzhou, 2016).CrossRefGoogle Scholar 37. H. Mohimani, M. Babaie-Zadeh, C. Jutten, A fast approach for overcomplete sparse decomposition based on smoothed l 0 norm. IEEE Trans. Signal Process.57(1), 289–301 (2009).MathSciNetzbMATHCrossRefGoogle Scholar 38. A. Ghaffari, M. Babaie-Zadeh, C. Jutten, Sparse decomposition of two dimensional signals (IEEE International Conference on Acoustics, Speech and Signal Processing (ICASSP), Taipei, 2009).CrossRefGoogle Scholar 39. N. Kolomvakis, M. Matthaiou, M. Coldrey, Massive MIMO in sparse channels (IEEE International Workshop on Signal Processing Advances in Wireless Communications (SPAWC), Toronto, 2014).CrossRefGoogle Scholar 40. D.L. Donoho, Compressed sensing. IEEE Trans. Inf. Theory. 52(4), 1289–1306 (2006).MathSciNetzbMATHCrossRefGoogle Scholar Copyright information © The Author(s) 2018 Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. Authors and Affiliations Xinrong Ye12Email authorView author's OrcID profileAiqing Zhang2Gan Zheng3Li You1Xiqi Gao11.National Mobile Communications Research Laboratory, Southeast UniversityNanjingPeople’s Republic of China2.College of Physics and Electronic Information, Anhui Normal UniversityWuhuPeople’s Republic of China3.Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough UniversityLoughboroughUK


This is a preview of a remote PDF: https://link.springer.com/content/pdf/10.1186%2Fs13638-018-1252-9.pdf

Xinrong Ye, Aiqing Zhang, Gan Zheng, Li You, Xiqi Gao. Multicell multiuser massive MIMO channel estimation and MPSK signal block detection applying two-dimensional compressed sensing, EURASIP Journal on Wireless Communications and Networking, 2018, 238, DOI: 10.1186/s13638-018-1252-9